Ugenz Academy/IoT Tutorial

Sound And Vibration Sensors

13 min read2,451 words

Reading progress

Keep learning

Sound and Vibration Sensors

Sound and vibration sensors detect sound waves, noise, impacts, knocks, mechanical vibrations, and oscillations.

They are useful in:

  • Security systems
  • Machinery monitoring
  • Robotics
  • Smart homes
  • Industrial automation
  • Noise monitoring
  • Vehicle systems
  • Earthquake/impact detection
  • IoT monitoring
  • Voice-controlled systems

Basic concept:

Sound / Vibration ↓ Sensor ↓ Electrical Signal ↓ Arduino / ESP32 ↓ Data Processing ↓ Alarm / Display / Action

1. What Is Sound?

Sound is a mechanical wave produced by vibrations and transmitted through a medium such as air.

For example:

Speaker ↓ Air vibrates ↓ Sound wave ↓ Microphone ↓ Electrical signal

A sound wave can be described using properties such as:

  • Frequency
  • Amplitude
  • Wavelength
  • Phase

2. Frequency

Frequency tells us how many cycles occur per second.

Unit:

Hertz (Hz)

For example:

100 Hz → 100 cycles/second

Higher frequency generally means a higher-pitched sound.

Low frequency → Low pitch High frequency → High pitch

3. Amplitude

Amplitude represents the magnitude of a wave.

For a sound signal:

Higher amplitude ↓ Stronger sound pressure

Simplified:

Low amplitude: ────╱╲────╱╲──── High amplitude: ───╱╲────╱╲────╱╲───

Amplitude is related to loudness, but perceived loudness also depends on frequency and human hearing.


4. Microphone Sensor

A microphone converts sound into an electrical signal.

Basic system:

Sound ↓ Microphone ↓ Electrical Signal ↓ ESP32 ↓ Processing

Microphones are used in:

  • Voice recording
  • Sound detection
  • Voice assistants
  • Noise monitoring
  • Security systems

5. Electret Microphone

A common microphone component in electronics is the electret microphone.

A module may contain:

Microphone ↓ Amplifier ↓ Analog / Digital Output

A microphone itself generates a relatively small signal, so an amplifier is often used.


6. Sound Sensor Module

Common hobby sound sensor modules may provide:

VCC GND AO DO

Where:

  • AO = Analog Output
  • DO = Digital Output

Concept:

Sound ↓ Microphone ↓ Amplifier ↓ ┌──────────────┐ │ AO → Analog │ │ DO → Digital │ └──────────────┘

7. Digital Sound Detection

The digital output normally uses a threshold.

For example:

Sound level < threshold ↓ LOW Sound level > threshold ↓ HIGH

The threshold can often be adjusted using a potentiometer on the module.


8. ESP32 Sound Detection

Example:

#define SOUND_PIN 27 #define LED_PIN 2 void setup() { Serial.begin(115200); pinMode(SOUND_PIN, INPUT); pinMode(LED_PIN, OUTPUT); } void loop() { int state = digitalRead(SOUND_PIN); if (state == HIGH) { digitalWrite(LED_PIN, HIGH); Serial.println("Sound detected"); } else { digitalWrite(LED_PIN, LOW); } delay(50); }

The exact HIGH/LOW behavior depends on the particular sound module.


9. Analog Sound Measurement

Analog output provides a continuously changing signal.

Sound ↓ Microphone ↓ Amplifier ↓ Analog waveform ↓ ADC ↓ ESP32

Example:

#define MIC_PIN 34 void setup() { Serial.begin(115200); } void loop() { int value = analogRead(MIC_PIN); Serial.println(value); delay(10); }

This gives an ADC reading, but the raw ADC value is not automatically a calibrated sound-pressure level in dB.


10. Sound Waveform

A microphone output can resemble:

Voltage /\ /\ /\ / \ / \ / \ / \___/ \___/ \___ ──────────────────────────────→ Time

The ESP32 can sample this waveform.

From the sampled signal, software can calculate properties such as:

  • Peak amplitude
  • RMS level
  • Frequency
  • Approximate sound level

11. Sampling

When a microcontroller measures an analog sound signal, it takes samples.

Continuous sound ↓ ADC sampling ↓ ● ● ● ● ● ● ● ● ↓ Digital data

The sampling rate is the number of samples taken per second.

For example:

10,000 samples/second = 10 kHz sampling rate

12. Nyquist Principle

To properly represent a signal, the sampling rate generally needs to be greater than twice the highest frequency of interest.

Fs > 2 × Fmax

For example, if you want to analyze frequencies up to 5 kHz:

Fs > 10 kHz

In practical systems, additional margin and appropriate filtering are important.


13. Sound Frequency Detection

If you want to determine the frequency of a sound, you can analyze the sampled waveform.

For example:

Microphone ↓ ADC ↓ Samples ↓ Frequency analysis ↓ 1000 Hz

Techniques such as FFT (Fast Fourier Transform) are commonly used.


14. FFT

FFT converts information from the time domain into the frequency domain.

Time domain:

Amplitude ↑ │ /\/\ /\/\ /\/\ └────────────────→ Time

Frequency domain:

Amplitude ↑ │ █ │ █ └────────┼────────→ Frequency 1 kHz

This allows us to identify dominant frequencies.


15. Sound Level and Decibels

Sound levels are commonly expressed in decibels (dB).

A simplified sound-pressure-level relationship is:

SPL = 20 log10(p / p₀)

where:

  • p = measured RMS sound pressure
  • p₀ = reference sound pressure

For air, the commonly used reference is:

p₀ = 20 µPa

However, simply reading an Arduino microphone module's ADC value and labeling it "dB" is not automatically accurate.

A calibrated microphone and appropriate calibration procedure are needed for reliable SPL measurements.


16. Why Cheap Sound Modules Aren't Proper Sound Meters

A typical hobby sound module may provide:

Microphone + Amplifier + Comparator

Its output depends on:

  • Microphone sensitivity
  • Amplifier gain
  • Supply voltage
  • Circuit design
  • Distance from sound source
  • Frequency
  • Environmental noise

Therefore:

ADC = 2500

does not universally mean:

70 dB

Calibration is required.


17. Vibration Sensors

A vibration sensor detects mechanical movement or oscillation.

Example:

Motor ↓ Mechanical vibration ↓ Vibration sensor ↓ ESP32

Vibration can indicate:

  • Normal operation
  • Imbalance
  • Mechanical impact
  • Loose components
  • Bearing problems
  • Machine faults

18. SW-420 Vibration Sensor

The SW-420 is a common hobby vibration sensor.

A typical module provides:

VCC GND DO

Inside, a vibration-sensitive mechanical element changes state when vibration occurs.

The module's comparator produces a digital signal.

Concept:

Vibration ↓ SW-420 ↓ Comparator ↓ Digital Output ↓ ESP32

19. SW-420 Example

#define VIBRATION_PIN 27 #define LED_PIN 2 void setup() { Serial.begin(115200); pinMode(VIBRATION_PIN, INPUT); pinMode(LED_PIN, OUTPUT); } void loop() { if (digitalRead(VIBRATION_PIN)) { Serial.println("Vibration detected"); digitalWrite(LED_PIN, HIGH); } else { digitalWrite(LED_PIN, LOW); } delay(50); }

The actual output polarity varies by module.


20. Piezoelectric Vibration Sensor

A piezoelectric sensor can generate an electrical signal when mechanically stressed or vibrated.

Concept:

Mechanical vibration ↓ Piezoelectric material ↓ Electrical signal

Piezo elements are commonly used for:

  • Knock detection
  • Vibration detection
  • Impact sensing
  • Acoustic pickup
  • Buzzers

21. Piezo Sensor

A piezo disc can be connected to a suitable input circuit.

Conceptually:

Piezo ├── Signal └── Ground ↓ ADC ↓ ESP32

The generated voltage can sometimes be surprisingly high during sharp impacts, so the input circuit should be designed to protect the microcontroller.

Do not blindly connect an unknown piezo element to an ESP32 ADC without considering voltage limiting/protection.


22. Piezo Knock Sensor

A piezo sensor can detect a knock on a surface.

Knock ↓ Surface vibrates ↓ Piezo ↓ Voltage pulse ↓ ESP32 ↓ "Knock detected"

Applications:

  • Smart doors
  • Security systems
  • Machine monitoring
  • Interactive devices

23. Accelerometer for Vibration

An accelerometer measures acceleration.

Common sensors include:

  • MPU6050
  • ADXL345
  • LIS3DH

A 3-axis accelerometer measures:

X-axis Y-axis Z-axis

Concept:

Z ↑ | ●────→ X / ↓ Y

24. Accelerometer vs Simple Vibration Sensor

FeatureSW-420Accelerometer
OutputUsually digitalDigital data
Vibration detectionYesYes
DirectionNoX/Y/Z
MagnitudeLimitedMeasurable
Motion analysisLimitedExcellent
Advanced analysisNoYes
Typical useSimple alarmMotion/vibration monitoring

25. MPU6050 for Vibration

The MPU6050 contains:

  • 3-axis accelerometer
  • 3-axis gyroscope

The accelerometer can measure changes in acceleration.

Machine ↓ Vibration ↓ MPU6050 ↓ Acceleration data ↓ ESP32 ↓ Analysis

You can monitor vibration over time.


26. Vibration Monitoring

Suppose a motor normally produces:

Normal: Small vibration

Later:

Abnormal: Large vibration

The ESP32 can compare the measured value with a threshold.

Vibration < threshold ↓ NORMAL Vibration > threshold ↓ WARNING

27. Predictive Maintenance

Industrial machines can be monitored continuously.

Machine ↓ Vibration Sensor ↓ ESP32 ↓ Data Logging ↓ Trend Analysis ↓ Maintenance Alert

For example:

Day 1 → Normal Day 10 → Slight increase Day 20 → Higher Day 30 → Abnormal

A rising vibration trend can indicate a possible mechanical problem.

However, proper diagnosis requires suitable sensors, mounting, signal processing, and domain-specific analysis.


28. Sound + Vibration Monitoring

You can combine both sensors.

MACHINE / \ ↓ ↓ Microphone Accelerometer ↓ ↓ └────┬────┘ ↓ ESP32 ↓ Machine Status

For example:

Normal sound + normal vibration ↓ NORMAL Abnormal sound + high vibration ↓ WARNING

This can provide more information than using one sensor alone.


29. Sound-Activated Light

A simple project:

Clap ↓ Microphone ↓ ESP32 ↓ Relay ↓ Light

Example logic:

Clap detected ↓ Light ON Second clap ↓ Light OFF

For a reliable clap detector, software should distinguish a clap from continuous background noise.


30. Vibration Security Alarm

A vibration sensor can be attached to a door/window.

Window ↓ Vibration Sensor ↓ ESP32 ↓ Buzzer

If someone shakes the window:

Vibration ↓ Sensor triggered ↓ ESP32 ↓ Alarm

31. Machine Health Monitor

A practical IoT project:

MOTOR ↓ ┌───────────────┐ │ │ ↓ ↓ Microphone Accelerometer ↓ ↓ └───────┬───────┘ ↓ ESP32 ↓ Wi-Fi / Cloud ↓ Dashboard

The dashboard could show:

Motor Status: NORMAL Vibration: LOW Sound: NORMAL Temperature: 34°C

32. Sound Sensor vs Microphone

These terms are often confused.

Microphone

Primarily converts sound into an electrical signal.

Sound Sensor Module

Usually combines:

Microphone + Amplifier + Comparator

and may provide a simple digital trigger.

Therefore:

Detailed audio analysis ↓ Microphone + ADC/audio interface Simple sound detection ↓ Sound sensor module

33. Digital vs Analog Sound Sensors

Digital

Sound > Threshold ↓ HIGH Sound < Threshold ↓ LOW

Good for:

  • Alarm
  • Clap detection
  • Simple triggering

Analog

Sound waveform ↓ Variable voltage ↓ ADC

Good for:

  • Signal analysis
  • Frequency detection
  • Relative amplitude analysis

34. Common Problems

Microphone

  • Background noise
  • Poor placement
  • Incorrect gain
  • ADC noise

Sound Module

  • Threshold incorrectly adjusted
  • False triggering
  • Not calibrated for dB measurement

Vibration Sensor

  • False triggers
  • Mechanical mounting issues
  • Excessive sensitivity

Accelerometer

  • Sensor orientation
  • Sensor noise
  • Sampling issues
  • Mechanical resonance

35. Filtering

Real-world sensor signals contain noise.

Example:

Raw signal ────────╱╲─╱╲──╱╲─╱╲────

Filtering can produce:

Filtered signal ──────╱╲────╱╲──────────

Common filtering concepts include:

  • Moving average
  • Low-pass filter
  • High-pass filter
  • Band-pass filter

The correct filter depends on what signal you want to preserve.


36. Sound and Vibration Frequency

Frequency analysis is useful for machinery.

For example:

Machine vibration ↓ Accelerometer ↓ Sampling ↓ FFT ↓ Frequency spectrum

Suppose a strong peak appears at:

50 Hz

That tells you the vibration signal has a strong component around 50 Hz.

The meaning of that frequency depends on the machine, rotational speed, harmonics, and mechanical system.


37. Practical Project: Knock-Controlled Device

Components:

  • Piezo sensor
  • ESP32
  • LED
  • Relay

Flow:

Knock ↓ Piezo ↓ ESP32 ↓ Detect pulse ↓ Toggle output

Example:

Knock → Light ON Knock → Light OFF

This is a good project for understanding event detection.


38. Practical Project: Vibration-Based Theft Alarm

Object ↓ Vibration Sensor ↓ ESP32 ↓ Timer / Verification ↓ Buzzer ↓ Alarm

A good design should avoid triggering on every tiny vibration. You can require:

Several vibration events within a short time ↓ Trigger alarm

39. Practical Project: Noise Monitor

Microphone ↓ ADC / Audio Interface ↓ ESP32 ↓ Signal Processing ↓ Relative Sound Level

Display:

┌──────────────────┐ │ SOUND MONITOR │ │ │ │ Level: HIGH │ │ Status: WARNING │ └──────────────────┘

For accurate legal/industrial noise measurement, use a calibrated measurement system rather than an uncalibrated hobby microphone.


40. Comparison Table

SensorDetectsOutputTypical Application
MicrophoneSoundAnalog/audioVoice/audio
Sound moduleSound level/eventAnalog/digitalSound trigger
SW-420VibrationDigitalSimple alarm
Piezo sensorVibration/impactAnalog pulseKnock detection
AccelerometerAcceleration/vibrationDigital dataMachine monitoring
GyroscopeAngular motionDigital dataMotion/orientation

41. Choosing the Right Sensor

Choose a microphone when:

You need an electrical representation of sound.

Choose a sound sensor module when:

You only need simple sound detection.

Choose a piezo sensor when:

You need impact or vibration detection.

Choose an SW-420 when:

You need inexpensive digital vibration detection.

Choose an accelerometer when:

You need vibration magnitude, direction, or detailed motion data.


42. Overall Concept

SOUND / VIBRATION ↓ ┌────────────┼─────────────┐ ↓ ↓ ↓ Microphone Piezo Accelerometer ↓ ↓ ↓ Sound Impact Acceleration ↓ ↓ ↓ └────────────┼─────────────┘ ↓ ESP32 ↓ Signal Processing ↓ ┌──────────────┼──────────────┐ ↓ ↓ ↓ Display Alarm IoT Cloud

Key Points

Sound → Mechanical wave that can be converted into an electrical signal. Microphone → Converts sound into an electrical signal. Frequency → Number of cycles per second, measured in Hz. Amplitude → Magnitude of the signal. Vibration Sensor → Detects mechanical vibration. Piezo Sensor → Converts mechanical stress/vibration into an electrical signal. Accelerometer → Measures acceleration and can be used for detailed vibration analysis. FFT → Useful for analyzing frequency components. dB → Common logarithmic unit for sound level, but accurate dB measurement requires appropriate calibration.

Keep learning. Keep building. Keep growing.

© 2026 Ugenz Academy