Ugenz Academy/IoT Tutorial

Magnetic And Position Sensors

12 min read2,230 words

Reading progress

Keep learning

Magnetic and Position Sensors

Magnetic and position sensors are used to detect magnetic fields, the presence or absence of magnets, the position of an object, rotation, angle, movement, or mechanical limits.

They are widely used in:

  • Robotics
  • Motors
  • Automatic doors
  • Security systems
  • Industrial automation
  • Encoders
  • Smart locks
  • Vehicle systems
  • Drones
  • CNC machines
  • Printers
  • IoT devices

Basic concept:

Magnetic Field / Mechanical Position ↓ Sensor ↓ Electrical Signal ↓ ESP32 / Arduino ↓ Processing / Logic ↓ Motor / Display / Alarm

1. What Are Magnetic Sensors?

A magnetic sensor detects the presence, strength, direction, or change of a magnetic field.

For example, place a magnet near a Hall-effect sensor:

Magnet 🧲 ↓ Magnetic Field ↓ Hall Sensor ↓ Output

The controller can then determine that the magnet is nearby.


2. What Are Position Sensors?

A position sensor determines where an object is located or how far/which direction it has moved.

Examples:

  • Linear position
  • Rotary position
  • Angular position
  • End position
  • Relative movement

For example:

Motor shaft ↓ Encoder ↓ Rotation information ↓ ESP32

3. Hall-Effect Sensor

One of the most important magnetic sensors is the Hall-effect sensor.

It works using the Hall effect.

When a magnetic field is applied to a suitable semiconductor while current flows through it, a voltage can develop across the material.

Simplified:

Current → ┌─────────────┐ │ Hall Sensor │ ← Magnetic Field └─────────────┘ ↓ Hall Voltage

The electronics inside the sensor convert this effect into a useful output.


4. Digital Hall Sensor

A digital Hall sensor generally behaves like a switch.

Example:

No Magnet → LOW Magnet → HIGH

However, the exact output polarity depends on the sensor/module.

A common module is based on the A3144 Hall-effect sensor.

Typical applications:

  • Magnet detection
  • Door position
  • Motor rotation
  • Wheel speed
  • Limit detection

5. Hall Sensor with ESP32

Basic connection:

Hall Sensor ESP32 VCC ──────────── 3.3V* GND ──────────── GND OUT ──────────── GPIO 27

* Check the exact sensor/module specifications before powering it.

Example:

#define HALL_PIN 27 void setup() { Serial.begin(115200); pinMode(HALL_PIN, INPUT); } void loop() { int state = digitalRead(HALL_PIN); if (state == LOW) { Serial.println("Magnet Detected"); } else { Serial.println("No Magnet"); } delay(200); }

The logic may be reversed depending on the particular Hall sensor.


6. Hall Sensor for Motor Rotation

A magnet can be attached to a rotating wheel.

🧲 \ \ Rotating wheel ┌─────────┐ │ │ └─────────┘ ↓ Hall Sensor

Every time the magnet passes the sensor:

Magnet passes ↓ Hall pulse ↓ ESP32 ↓ Count pulses

If one magnet produces one pulse per revolution:

RPM = Revolutions per minute

For example, if 10 revolutions occur in 1 second:

10 × 60 = 600 RPM

7. Reed Switch

A reed switch is a magnetically operated mechanical switch.

Inside a typical reed switch are two metal contacts inside a sealed glass tube.

Glass Tube ┌─────────────────────┐ │ Contact Contact│ │ \ / │ └─────────────────────┘

When a magnet approaches:

Magnet 🧲 ↓ Contacts change state

Depending on the type, the contacts may open or close when the magnet is nearby.


8. Reed Switch Example

A very common application is a door sensor.

Door Frame Door ┌────────┐ ┌──────┐ │ Reed │ 🧲 │Magnet│ │ Switch │ │ │ └────────┘ └──────┘

When the door closes:

Magnet near reed switch ↓ Switch changes state ↓ ESP32 ↓ Door = CLOSED

When the door opens:

Magnet moves away ↓ Switch changes state ↓ Door = OPEN

9. Reed Switch vs Hall Sensor

FeatureReed SwitchHall Sensor
TechnologyMechanical magnetic contactSemiconductor
Moving partsYesNo
WearPossibleVery low
SpeedLimited compared with electronic sensingHigh
PowerCan operate as a passive switchRequires power for typical IC versions
Common useDoor/window sensorSpeed/rotation/magnetic detection

10. Analog Hall Sensors

Not all Hall sensors are simply ON/OFF.

An analog Hall sensor can provide an output related to magnetic-field strength.

Concept:

Weak Magnetic Field ↓ Small Output Change Strong Magnetic Field ↓ Larger Output Change

This allows applications such as:

  • Magnetic field measurement
  • Current sensing
  • Position measurement
  • Motor control

11. Magnetic Field Sensor

Magnetic sensors can detect:

  • Presence of a magnet
  • Magnetic-field strength
  • Magnetic-field direction
  • Rotation
  • Position

More advanced magnetic sensors can measure multiple axes.

For example:

X-axis → Magnetic field Y-axis → Magnetic field Z-axis → Magnetic field

These are useful for electronic compasses and orientation systems.


12. Magnetometer

A magnetometer measures magnetic fields.

A common example is the HMC5883L, while newer sensor modules such as the QMC5883L are also commonly encountered in hobby projects.

A 3-axis magnetometer can measure:

X → Magnetic field Y → Magnetic field Z → Magnetic field

This can be used to estimate heading.


13. Electronic Compass

A magnetometer can act as an electronic compass.

Concept:

Earth's Magnetic Field ↓ Magnetometer ↓ ESP32 ↓ Direction

For example:

North ↑ | | 🚗

The controller can estimate the direction the device is facing.

However, nearby metal, motors, magnets, and electrical currents can distort the magnetic field.


14. Potentiometer as a Position Sensor

A potentiometer is a variable resistor.

It has three main terminals:

Potentiometer ┌─────────┐ VCC ─┤ ├─ GND │ ↑ │ │ Wiper │ └────┬────┘ │ OUT

The wiper position changes the output voltage.

Therefore:

Knob Position ↓ Resistance Ratio ↓ Output Voltage ↓ ADC ↓ Digital Value

This allows the controller to estimate the knob's position.


15. Potentiometer with ESP32

Example:

#define POT_PIN 34 void setup() { Serial.begin(115200); } void loop() { int value = analogRead(POT_PIN); Serial.println(value); delay(200); }

The exact ADC behavior and usable resolution depend on the ESP32 variant and configuration.


16. Potentiometer Applications

A potentiometer can be used as:

  • Volume control
  • Motor speed control
  • Servo angle input
  • Menu control
  • Brightness control
  • Position input

Example:

Potentiometer ↓ ESP32 ↓ Servo

Rotate the potentiometer:

0° → Servo 0° 50% → Servo ~90° 100% → Servo ~180°

The exact mapping depends on software and servo limits.


17. Rotary Encoder

A rotary encoder detects rotational movement.

Unlike a simple potentiometer, an encoder can provide information about:

  • Direction
  • Relative rotation
  • Number of steps

A common incremental encoder has:

A B

signals.

Sometimes it also has:

SW

for a push-button.


18. How a Rotary Encoder Works

When the shaft rotates:

Rotation ↓ Encoder ↓ A and B pulses ↓ ESP32 ↓ Direction + Position

The A and B signals are offset in phase.

Simplified:

A: ──██──██──██── B: ────██──██──██

The relationship between A and B tells the controller which direction the shaft is rotating.


19. Rotary Encoder Applications

Used in:

  • CNC machines
  • 3D printers
  • Robot wheels
  • Motor control
  • Digital menus
  • Volume knobs
  • Industrial machines

Example:

Rotate clockwise ↓ Encoder ↓ Increase value Rotate counter-clockwise ↓ Encoder ↓ Decrease value

20. Incremental vs Absolute Encoder

Incremental Encoder

Reports changes in position.

Movement → Pulses

The controller usually needs to maintain a count.

Absolute Encoder

Reports an actual position value.

Shaft Position ↓ Encoder ↓ Absolute Position

Even after power loss, an absolute encoder can provide its position when read, depending on its technology and mechanical setup.


21. Limit Switch

A limit switch detects whether a mechanical object has reached a particular position.

Example:

Moving Mechanism ↓ ↓ ───────┐ │ [Limit Switch]

When the mechanism reaches the switch:

Mechanical contact ↓ Switch activated ↓ ESP32 ↓ STOP MOTOR

This is extremely important in:

  • CNC machines
  • 3D printers
  • Linear actuators
  • Robotic arms
  • Automatic doors

22. Limit Switch for Motor Safety

Suppose a motor moves a platform.

Motor → Platform →→→→→ [LIMIT]

Without a limit switch:

Motor keeps running ↓ Mechanical collision ↓ Possible damage

With a limit switch:

Platform reaches limit ↓ Switch activated ↓ ESP32 ↓ Motor STOP

23. Linear Position Sensors

Some systems need to know linear position rather than rotation.

Examples include:

  • Linear potentiometer
  • Linear encoder
  • LVDT
  • Magnetic linear sensor

Example:

Moving Object ↓ ─────────────●───────────── ↑ Position Sensor

The sensor tells the controller where the object is along the axis.


24. Angle Sensors

An angle sensor measures angular position.

For example:

Arm / / ● ↑ Rotation

Applications:

  • Robotic arms
  • Steering systems
  • Servo mechanisms
  • Joysticks
  • Industrial machines

Technologies include:

  • Potentiometers
  • Magnetic angle sensors
  • Encoders
  • Optical encoders

25. Magnetic Position Detection

A magnet and Hall sensor can work together as a position detector.

Moving Part 🧲 ↓ Hall Sensor ↓ ESP32

Multiple Hall sensors can provide multiple positions:

Position 1 → Hall Sensor 1 Position 2 → Hall Sensor 2 Position 3 → Hall Sensor 3

This can be useful for detecting the position of mechanical components.


26. Wheel Speed Measurement

A magnet can be attached to a wheel.

🧲 ┌───────┐ ┌──┤ Wheel ├──┐ │ └───────┘ │ │ │ └──────↓──────┘ Hall Sensor

Every rotation produces a pulse.

If wheel circumference is known:

Speed = Distance / Time

For one pulse per revolution:

Distance per pulse = Wheel Circumference

Then the ESP32 can calculate speed.


27. Smart Door Security

Magnetic sensors are excellent for door/window monitoring.

Door │ ├── Magnet │ └── Reed/Hall Sensor ↓ ESP32 ↓ Security

Example logic:

Door CLOSED ↓ Normal Door OPEN ↓ Sensor triggered ↓ ESP32 ↓ Alarm / Notification

28. Magnetic vs Position Sensors

These categories overlap.

SensorMain Purpose
Hall sensorMagnetic field / magnet detection
Reed switchMagnetic ON/OFF switching
MagnetometerMagnetic-field measurement
PotentiometerPosition/angle
Rotary encoderRotation/direction
Limit switchEnd-position detection
Linear encoderLinear position
Magnetic encoderRotation/position

29. Practical ESP32 Project

Smart Door Position Monitor

Components:

  • ESP32
  • Reed switch
  • Magnet
  • Buzzer
  • LED

Connection concept:

Reed Switch ↓ ESP32 GPIO ↓ ┌────┴─────┐ ↓ ↓ LED Buzzer

Logic:

Door Closed ↓ LED OFF Buzzer OFF Door Open ↓ LED ON Buzzer ON

30. Motor Position Control

A more advanced system can combine:

Motor ↓ Encoder ↓ ESP32 ↓ Motor Driver ↓ Motor

This creates a feedback system:

Desired Position ↓ Controller ↓ Motor Driver ↓ Motor ↓ Encoder ↓ Actual Position ↓ Feedback └────────→ Controller

This is the basic idea behind closed-loop control.


31. Open Loop vs Closed Loop

Open Loop

Controller ↓ Motor

The controller doesn't directly measure the actual position.

Closed Loop

Controller ↓ Motor ↓ Encoder ↓ Feedback └────→ Controller

Closed-loop systems can correct errors based on feedback.


32. Common Problems

Hall Sensor

  • Wrong magnet orientation
  • Insufficient magnetic field
  • Incorrect output logic
  • Electrical noise

Reed Switch

  • Mechanical wear
  • Contact bounce
  • Incorrect magnet distance

Encoder

  • Missed pulses at high speed
  • Incorrect A/B interpretation
  • Electrical noise
  • Software counting errors

Potentiometer

  • Mechanical wear
  • Noisy ADC readings
  • Poor connections

Limit Switch

  • Contact bounce
  • Incorrect switch placement
  • Mechanical damage

33. Sensor Selection Guide

Choose Hall sensor when you need:

Magnet detection or rotational sensing.

Choose reed switch when you need:

Simple magnetic ON/OFF detection.

Choose magnetometer when you need:

Magnetic-field measurement or compass functionality.

Choose potentiometer when you need:

Simple manual position/angle input.

Choose rotary encoder when you need:

Rotation, direction, and relative position.

Choose limit switch when you need:

Mechanical end-position detection.

Choose linear encoder when you need:

Precise linear position measurement.


Key Points to Remember

Hall Sensor → Detects magnetic fields Reed Switch → Magnetically operated switch Magnetometer → Measures magnetic field Potentiometer → Measures position/angle through voltage Rotary Encoder → Measures rotation and direction Limit Switch → Detects mechanical end position Linear Encoder → Measures linear position Magnetic Encoder → Measures rotational position using magnetic sensing

The overall concept is:

MAGNET / MOVEMENT / POSITION ↓ ┌───────────┼───────────┐ ↓ ↓ ↓ Hall Reed Encoder ↓ ↓ ↓ Magnetic ON/OFF Position Field State /Rotation └───────────┼───────────┘ ↓ ESP32 ↓ Decision / Control ↓ Motor / Alarm / Display

Keep learning. Keep building. Keep growing.

© 2026 Ugenz Academy