Ugenz Academy/IoT Tutorial

Analog And Digital Sensors

7 min read1,382 words

Reading progress

Keep learning

Analog and Digital Sensors

After understanding what a sensor is, the next important concept is how sensors provide their output.

Sensors are commonly classified based on their output into:

  1. Analog Sensors
  2. Digital Sensors

1. Analog Sensors

An analog sensor produces a continuous electrical signal that changes according to the physical quantity being measured.

The output can have many different values within a particular range.

For example, an analog temperature sensor might produce:

Temperature Output Voltage 10°C 0.10 V 20°C 0.20 V 30°C 0.30 V 40°C 0.40 V

The output continuously changes as the temperature changes.

Simple representation

Physical Quantity ↓ Analog Sensor ↓ Continuous Signal ↓ Microcontroller ADC ↓ Digital Value

Example: LDR

An LDR (Light Dependent Resistor) changes its resistance according to the amount of light.

More Light ↓ LDR Resistance Changes ↓ Voltage Changes ↓ Arduino / ESP32 reads voltage

For example:

Dark → Low/High voltage depending on circuit Dim Light → Different voltage Bright → Different voltage

The exact voltage depends on how the LDR is connected in the circuit.


Example: LM35

The LM35 is an analog temperature sensor.

Its output voltage changes approximately linearly with temperature.

Conceptually:

Temperature ↑ ↓ Output Voltage ↑

An Arduino or ESP32 reads the voltage through an ADC (Analog-to-Digital Converter).


What is ADC?

A microcontroller works internally with digital values, but an analog sensor produces a continuous voltage.

Therefore, we need a conversion:

Analog Voltage ↓ ADC ↓ Digital Number

ADC = Analog-to-Digital Converter

For example, suppose an ADC has a range from:

0 V → 3.3 V

and produces values:

0 → 4095

Then:

0 V → 0 1.65 V → approximately 2048 3.3 V → 4095

This is typical of a 12-bit ADC over a 0–3.3 V range, although the exact usable range and behavior depend on the microcontroller.


ADC Resolution

ADC resolution determines how many digital levels can represent the analog input.

8-bit ADC

2⁸ = 256 levels 0 → 255

10-bit ADC

2¹⁰ = 1024 levels 0 → 1023

12-bit ADC

2¹² = 4096 levels 0 → 4095

Therefore:

Higher ADC resolution allows the input voltage to be represented using more digital levels.

However, higher nominal resolution does not automatically mean higher real-world measurement accuracy.


2. Digital Sensors

A digital sensor provides data in a digital form.

For simple digital sensors, the output may be:

LOW → 0 HIGH → 1

For example, a digital motion sensor may provide:

No Motion → LOW Motion → HIGH

Example: PIR Sensor

A PIR motion sensor can detect human movement.

Its digital output might behave like:

No motion ↓ LOW Motion detected ↓ HIGH

The microcontroller reads this using a digital input pin.

PIR ↓ Digital GPIO ↓ ESP32

Digital Sensors Can Also Send Data

Not every digital sensor simply outputs HIGH or LOW.

Many modern sensors communicate using digital communication protocols.

Common protocols include:

  • I²C
  • SPI
  • UART
  • 1-Wire

For example:

BME280 ↓ I²C ↓ ESP32

The BME280 can provide digital measurements such as:

  • Temperature
  • Humidity
  • Atmospheric pressure

Analog vs Digital

FeatureAnalog SensorDigital Sensor
OutputContinuous signalDigital signal/data
Typical outputVoltage/current/resistanceHIGH/LOW or digital data
ADC requiredUsually yesUsually no for digital interface
Noise sensitivityCan be more affected by analog noiseOften better suited to digital processing
ExamplesLDR, LM35, potentiometerDHT22, BME280, digital PIR
InterfaceADC pin/circuitGPIO, I²C, SPI, UART, etc.

Important: Sensor vs Output Type

A sensor itself isn't always permanently "analog" or "digital" in every implementation.

For example, the same physical quantity, such as temperature, can be measured using:

Analog temperature sensor

LM35 ↓ Analog voltage ↓ ADC ↓ Temperature value

Digital temperature sensor

DS18B20 ↓ Digital data ↓ Microcontroller ↓ Temperature value

Both measure temperature, but they provide the information differently.


Analog Sensor Connection with Arduino

Example using an LDR:

5V │ LDR │ ├──────── A0 │ Resistor │ GND

The LDR and resistor form a voltage divider.

Arduino reads the voltage at A0.

int value = analogRead(A0); Serial.println(value);

The result depends on the Arduino board and ADC configuration.

For a typical Arduino Uno:

0 V → approximately 0 5 V → approximately 1023

because the Uno's default ADC is 10-bit.


Analog Sensor with ESP32

ESP32 boards have ADC-capable GPIOs.

For example:

#define SENSOR_PIN 34 void setup() { Serial.begin(115200); } void loop() { int value = analogRead(SENSOR_PIN); Serial.println(value); delay(500); }

The ESP32 reads the analog sensor and converts the input into a digital ADC reading.

Important: ESP32 ADC behavior depends on the specific ESP32 chip/board and configuration, so don't assume every board has exactly the same ADC characteristics.


Digital Sensor Connection

For a simple digital sensor:

Sensor │ ├── VCC ├── GND └── OUT │ ↓ ESP32 GPIO

Example:

#define SENSOR_PIN 27 void setup() { Serial.begin(115200); pinMode(SENSOR_PIN, INPUT); } void loop() { int state = digitalRead(SENSOR_PIN); if (state == HIGH) { Serial.println("Detected"); } else { Serial.println("Not Detected"); } delay(500); }

Analog Signal vs Digital Signal

Imagine a sensor measuring light intensity.

Analog

The signal can continuously change:

0.0V 0.4V 0.8V 1.2V 1.7V 2.1V 2.8V 3.3V

Digital

A simple digital sensor may report:

0 → No detection 1 → Detection

Or a digital communication sensor can send a complete numerical value, such as:

Temperature = 28.6°C Humidity = 64%

Advantages of Analog Sensors

  • Simple circuit design for many applications
  • Continuous measurement
  • Often inexpensive
  • Useful when the exact magnitude of a physical quantity is needed
  • Can be directly interfaced with ADC inputs

Disadvantages

  • Analog signals can be affected by electrical noise
  • Usually require ADC conversion
  • Long wires can introduce interference
  • Signal conditioning may be required
  • Accuracy depends on the sensor, circuit, ADC, reference, and noise

Advantages of Digital Sensors

  • Easy to process using microcontrollers
  • Digital communication can provide multiple measured values
  • Often includes signal conditioning inside the sensor
  • Less concern about analog voltage interpretation at the microcontroller input
  • Can communicate using standard protocols such as I²C and SPI

Disadvantages

  • Communication protocol is required for many sensors
  • Some digital sensors are more expensive
  • Software libraries may be required
  • Protocol/address conflicts can occur in larger systems

Examples of Analog Sensors

Common examples include:

  • LDR
  • LM35
  • Potentiometer
  • Analog soil-moisture sensor
  • Thermistor
  • FSR
  • Many MQ-series gas sensor modules

Examples of Digital Sensors

Common examples include:

  • DHT11
  • DHT22
  • DS18B20
  • BME280
  • MPU6050
  • Digital PIR modules
  • Digital Hall-effect sensors
  • VL53L0X

Some of these use a dedicated digital communication protocol rather than simply outputting HIGH/LOW.


Real-World Example: Automatic Street Light

Suppose we want to automatically turn ON a street light at night.

Using an analog LDR

Light ↓ LDR ↓ Analog Voltage ↓ Arduino/ESP32 ADC ↓ Program checks light level ↓ Relay ↓ Light

Example logic:

If light level < threshold ↓ DARK ↓ Light ON

Real-World Example: Motion Alarm

Using a digital PIR sensor:

Human Movement ↓ PIR Sensor ↓ Digital HIGH ↓ ESP32 ↓ Buzzer ↓ Alarm

Key Concept

The easiest way to remember the difference is:

ANALOG Physical Quantity ↓ Sensor ↓ Continuous Signal ↓ ADC ↓ Digital Number
DIGITAL Physical Quantity ↓ Sensor ↓ Digital Signal/Data ↓ Microcontroller

In one sentence:

Analog sensors provide continuously varying signals, while digital sensors provide discrete digital states or digital data that a microcontroller can process directly.

Keep learning. Keep building. Keep growing.

© 2026 Ugenz Academy