Ugenz Academy/IoT Tutorial

Oscillators

7 min read1,306 words

Reading progress

Keep learning

Oscillators in Electronics

1. Introduction

An oscillator is an electronic circuit that generates a continuous, repeating signal without requiring a repeating input signal.

Oscillators convert energy from a DC power supply into a periodic AC signal, such as a sine wave, square wave, or triangular wave.

They are widely used in clocks, radio transmitters, computers, microcontrollers, communication systems, and signal generators.

File:Waveforms.svg - Wikimedia Commons

Crystal Oscillator Package Types | Cadence

Fnirsi 1C15 oscilloscope

8

For example, a microcontroller needs a clock signal to coordinate its internal operations. A crystal oscillator can provide this stable timing signal.

2. Basic Working Principle

An oscillator works by using an amplifier and a feedback network to maintain a repeating electrical signal.

The main stages are:

  1. Power supply: Provides electrical energy to the circuit.
  2. Amplifier: Increases the signal and compensates for energy losses.
  3. Feedback network: Returns a portion of the output signal to the input with the required phase and frequency characteristics.
  4. Frequency-determining components: Resistors, capacitors, inductors, or crystals determine the oscillation frequency.

Conceptual oscillator block diagram. The feedback network helps establish the frequency and phase required for sustained oscillation.

3. Conditions for Oscillation

For an amplifier with feedback to sustain oscillation, it must satisfy the Barkhausen conditions at the oscillation frequency, in the ideal linear feedback model.

A. Loop gain

The magnitude of the loop gain must be approximately one:

∣Aβ∣=1\boxed{|A\beta|=1}

Where:

  • AA = amplifier gain
  • β\beta = feedback factor
  • AβA\beta = loop gain

If the loop gain is too small, oscillations tend to die away. If it is too large, the amplitude may grow until nonlinear effects limit it.

B. Phase condition

The total phase shift around the feedback loop must be an integer multiple of 360∘360^\circ:

∠Aβ=0∘(mod360∘)\boxed{\angle A\beta=0^\circ\pmod{360^\circ}}

This ensures that the feedback signal reinforces the oscillation rather than cancelling it.

These conditions describe the ideal steady-state requirement; a practical oscillator generally needs sufficient loop gain during startup and then stabilizes its amplitude.

4. Types of Oscillators

Oscillators are commonly classified by the waveform they produce and the method used to determine their frequency.

A. RC Oscillator

An RC oscillator uses resistors and capacitors in its frequency-selective feedback network.

Osilator Pergeseran Fasa RC: Prinsip Kerja dan Aplikasinya - Belajar Elektronika

abdulelektro.blogspot.com

Characteristics:

  • Commonly used to generate audio-frequency signals.
  • Does not require an inductor in its frequency-setting network.
  • Often used in phase-shift and Wien bridge oscillator circuits.

Applications: Audio signal generators, laboratory circuits, and low-frequency electronic systems.

B. LC Oscillator

An LC oscillator uses an inductor (LL) and capacitor (CC) to establish a resonant frequency.

Draw The Circuit Diagram Of A Colpitts Oscillator Explain Its Working

circuitdiagram.co

Characteristics:

  • Uses energy exchange between the inductor's magnetic field and the capacitor's electric field.
  • Commonly used at radio frequencies.
  • Examples include Hartley and Colpitts oscillators.

Applications: Radio transmitters, RF circuits, and communication equipment.

C. Crystal Oscillator

A crystal oscillator uses the mechanical resonance of a piezoelectric crystal, usually quartz, to produce a stable electrical frequency.

Crystal Oscillator Package Types | Cadence

resources.pcb.cadence.com

Characteristics:

  • Offers high frequency stability.
  • Is less affected by component variations than many simple RC or LC oscillators.
  • Is available in standard frequencies such as 8 MHz, 16 MHz, and 32.768 kHz.

Applications: Microcontrollers, digital clocks, computers, and communication devices.

D. Relaxation Oscillator

A relaxation oscillator repeatedly charges and discharges a capacitor or uses another switching mechanism to create a repeating waveform.

Multivibrators: PHC504

people.iitism.ac.in

Characteristics:

  • Commonly produces square, rectangular, or triangular waveforms.
  • Often uses switching thresholds to control charging and discharging.
  • Can be built using a 555 timer, a Schmitt trigger, or other switching circuits.

Applications: LED flashers, timing circuits, pulse generators, and alarms.

5. Common Oscillator Waveforms

Oscillators can produce different types of repeating signals depending on their circuit design.

Dynamic Voltage vs. 4-20 mA Proximity Probes Explained | CTC

Sine wave

A smooth, periodic waveform used in audio generation, RF systems, and signal testing.

Course: Circuiti digitali, porte logiche e famiglie

Square wave

Alternates between high and low levels. It is useful for digital clocks, switching, and timing.

Applied Function Generators | Tutorials on Electronics | Next Electronics

Triangular wave

Rises and falls approximately linearly. It is used in waveform generators and modulation circuits.

6. Important Oscillator Formulas

A. Frequency and time period

Frequency is the number of complete cycles generated per second.

f=1T\boxed{f=\frac{1}{T}}

Where:

  • ff = frequency in hertz (Hz)
  • TT = time period in seconds (s)

For example, if an oscillator completes one cycle every 0.0010.001 seconds:

f=10.001f=\frac{1}{0.001} f=1000 Hz=1 kHz\boxed{f=1000\text{ Hz}=1\text{ kHz}}

B. LC resonant frequency

For an ideal LC resonant network:

f0=12πLC\boxed{f_0=\frac{1}{2\pi\sqrt{LC}}}

Where LL is in henries and CC is in farads.

For example, if L=100,μHL=100\\,\mu H and C=100,pFC=100\\,pF:

f0=12π(100×10−6)(100×10−12)f_0=\frac{1}{2\pi\sqrt{(100\times10^{-6})(100\times10^{-12})}} f0≈1.59 MHz\boxed{f_0\approx1.59\text{ MHz}}

This is the ideal tank circuit's resonant frequency. The actual oscillator frequency can differ because of the active circuit and parasitic components.

C. RC phase-shift oscillator

For a common three-section RC phase-shift oscillator with equal resistors and capacitors, under the standard idealized assumptions:

f0≈12πRC6\boxed{f_0\approx\frac{1}{2\pi RC\sqrt{6}}}

This formula applies to the conventional circuit arrangement and assumes the loading effects are suitably small or accounted for.

For R=10,kΩR=10\\,k\Omega and C=10,nFC=10\\,nF:

f0≈12π(10,000)(10×10−9)6f_0\approx\frac{1}{2\pi(10\\,000)(10\times10^{-9})\sqrt6} f0≈650 Hz\boxed{f_0\approx650\text{ Hz}}

The exact result depends on the oscillator topology and loading.

7. Comparison of Oscillator Types

FeatureRC oscillatorLC oscillatorCrystal oscillatorRelaxation oscillator
Frequency-setting methodResistor and capacitorInductor and capacitorCrystal resonanceCharging, discharging, switching
Typical outputSine waveSine-like waveStable periodic signalSquare or triangular wave
Frequency stabilityModerateModerateHighDepends on circuit
Common useAudio signalsRF signalsDigital clocksTiming and pulses

8. Applications of Oscillators

Bit-Banged Async Serial Output And Disciplined Engineering - Steve Branam

Microcontrollers and computers

Provide clock signals that coordinate instruction execution and digital operations.

433MHz FM RF Transmitter Module with Transmit Range up to 300m — StampyTools

Radio communication

Generate carrier signals used to transmit information wirelessly.

Circuit design 555 Blinking LED - Tinkercad

Timing circuits

Produce repeating pulses for LED blinkers, alarms, and counters.

Waveform and Function Generators | Keysight

Signal generators

Produce test waveforms for testing and troubleshooting electronic circuits.

Elektronik-Workshop - Alarm Clock

Digital clocks and watches

Use stable crystal oscillators to maintain accurate timing.

9. Oscillator vs. Amplifier

FeatureOscillatorAmplifier
Main purposeGenerates a repeating signalIncreases the strength of an input signal
Input signalDoes not need a repeating external inputNormally requires an input signal
FeedbackUsually essential for sustained oscillationMay use feedback for gain or stability
ExampleCrystal clock oscillatorAudio amplifier

An oscillator still needs a DC power source and an initial disturbance or noise to start operating. It then sustains the repeating output through its circuit design.

10. Summary

An oscillator is an important electronic circuit that generates periodic signals. Its frequency and waveform depend on the feedback network and frequency-determining components.

Remember these key points:

  • RC oscillator: Uses resistors and capacitors.
  • LC oscillator: Uses an inductor and capacitor.
  • Crystal oscillator: Provides highly stable frequency generation.
  • Relaxation oscillator: Commonly generates square or triangular waveforms.
  • Frequency: f=1/Tf=1/T.
  • LC resonant frequency: f0=1/(2πLC)f_0=1/(2\pi\sqrt{LC}).

Oscillators are essential in timing, communication, digital electronics, and signal generation.

Keep learning. Keep building. Keep growing.

© 2026 Ugenz Academy