Ugenz Academy/IoT Tutorial

Amplifiers

7 min read1,397 words

Reading progress

Keep learning

Amplifiers in Electronics

1. Introduction

An amplifier is an electronic circuit that increases the amplitude of an input signal, producing a stronger output signal.

Amplifiers are used to increase voltage, current, or power so that a signal can be processed, transmitted, or used to drive another circuit.

For example, a microphone produces a small electrical signal. An audio amplifier increases the signal's power so that a speaker can produce audible sound.

The Transistor AmplifierProject

450W + 450W two-channel high-performance amplifier Uganda | Ubuy

Audio Amplifier with Common Transistors · One Transistor

11

An amplifier does not create energy from nothing. It uses energy from a power supply to produce a larger output signal.

2. Basic Working Principle

An amplifier receives a small input signal and uses a power supply and active components, such as transistors or operational amplifiers, to produce an amplified output.

Basic amplifier block diagram.

The working process is:

  1. A weak electrical signal enters the amplifier.
  2. The active component controls energy drawn from the power supply.
  3. The output signal becomes stronger while ideally retaining the input's information.
  4. The output drives the next stage or a load, such as a speaker.

An amplifier may also invert the signal or introduce distortion, depending on its design and operating conditions.

3. Types of Amplifiers According to the Quantity Amplified

A. Voltage Amplifier

A voltage amplifier increases the voltage amplitude of an input signal.

  • Input: Small voltage signal
  • Output: Larger voltage signal
  • Common application: Sensor signal conditioning and audio preamplifiers

For example, an input of 0.1 V0.1\text{ V} amplified by a factor of 20 produces an output of 2 V2\text{ V}, assuming the amplifier has sufficient supply voltage and operates within its limits.

B. Current Amplifier

A current amplifier increases the current available at its output relative to the input current.

  • Common application: Driving loads that require more current
  • Examples: Transistor current-amplifier stages and current buffers

C. Power Amplifier

A power amplifier delivers increased signal power to a load.

  • Common application: Speakers, transmitters, and motor-driving stages
  • Important considerations: Output power, efficiency, heat, and distortion

Power amplification usually requires energy from the power supply; the output power can be much greater than the signal power provided at the input.

4. Types of Amplifiers According to Circuit Design

A. Transistor Amplifier

A transistor amplifier uses a BJT or FET to amplify an electrical signal. A small input signal controls a larger current supplied by the power source.

Bipolar Junction Transistor (BJT) as an Amplifier

electricalvolt.com

Applications: Audio amplifiers, sensor circuits, radio-frequency stages, and electronic switching or control circuits.

B. Operational Amplifier (Op-Amp)

An op-amp is a high-gain differential amplifier that is commonly used with external feedback components to control its gain and behavior.

AcaDraw - AI Science Drawing Tool | Create Scientific Illustrations in Seconds

acadraw.com

Applications: Sensor conditioning, active filters, mathematical circuits, and signal processing.

C. Audio Amplifier

An audio amplifier increases the strength of audio-frequency signals so they can drive headphones or loudspeakers.

400 Watts Mono Amplifier Board DIY Toshiba 2SC5200 Transistor NPN and PNP_ELECTROINDIA - Share Project - PCBWay

pcbway.com

Applications: Speakers, televisions, public-address systems, and home audio equipment.

D. RF Amplifier

An RF (radio-frequency) amplifier increases signals at radio frequencies while being designed to operate over a particular frequency range.

Applications: Wireless receivers, transmitters, antennas, and communication systems.

5. Amplifier Gain

Gain describes how much an amplifier increases a signal's amplitude or power.

A. Voltage gain

Av=V_outV_in\boxed{A_v=\frac{V\_{\text{out}}}{V\_{\text{in}}}}

Where:

  • AvA_v = voltage gain
  • V_outV\_{\text{out}} = output voltage
  • V_inV\_{\text{in}} = input voltage

Example: An amplifier receives 0.2 V0.2\text{ V} and produces 4 V4\text{ V}.

Av=40.2A_v=\frac{4}{0.2} Av=20\boxed{A_v=20}

The voltage gain is 20.

B. Current gain

Ai=I_outI_in\boxed{A_i=\frac{I\_{\text{out}}}{I\_{\text{in}}}}

If the input current is 2 mA2\text{ mA} and the output current is 40 mA40\text{ mA}:

Ai=402A_i=\frac{40}{2} Ai=20\boxed{A_i=20}

The current gain is 20.

C. Power gain

Ap=P_outP_in\boxed{A_p=\frac{P\_{\text{out}}}{P\_{\text{in}}}}

If the input signal power is 5 mW5\text{ mW} and the output signal power is 100 mW100\text{ mW}:

Ap=1005A_p=\frac{100}{5} Ap=20\boxed{A_p=20}

The power gain is 20.

6. Gain in Decibels (dB)

Gain is often expressed in decibels (dB), particularly when comparing amplifier performance.

For voltage gain, when input and output impedances are equal:

Gv=20log⁡_10∣Av∣\boxed{G_v=20\log\_{10}|A_v|}

For power gain:

Gp=10log⁡_10(Ap)\boxed{G_p=10\log\_{10}(A_p)}

For example, if the voltage gain is 10:

Gv=20log⁡_10(10)G_v=20\log\_{10}(10) Gv=20 dB\boxed{G_v=20\text{ dB}}

A gain of 20 dB corresponds to a tenfold increase in voltage amplitude under the stated impedance condition.

7. Common BJT Amplifier Configurations

A bipolar junction transistor (BJT) can be connected in three common amplifier configurations.

BJT Transistor: Understanding the Fundamentals, Types, and Applications -

Common-emitter amplifier

Provides voltage and current gain. Its output voltage is normally inverted relative to the input in the usual operating configuration.

Typical use: General-purpose signal amplification.

PPT - Understanding BJT Amplifiers: Lab Session, Midterm Notes, and Emitter Follower Analysis PowerPoint Presentation - ID:6610758

Common-collector amplifier

Also called an emitter follower. It has voltage gain close to one, but can provide current gain and impedance buffering.

Typical use: Driving a load without heavily loading the previous stage.

Common Base Amplifier - Electrical Engineering (EE) PDF Download

Common-base amplifier

Has low input resistance and can provide voltage gain with no phase inversion between input and output voltages in its standard configuration.

Typical use: Certain high-frequency amplifier stages.

8. Classes of Power Amplifiers

Power amplifiers are classified by how their active devices conduct during each input signal cycle.

Class A

The active device conducts throughout the entire 360∘360^\circ signal cycle.

  • Good linearity and low distortion in a well-designed circuit.
  • Generally lower efficiency.
  • Used in some high-quality audio and small-signal circuits.

Class B

Each output device conducts for approximately 180∘180^\circ of the signal cycle in a push-pull arrangement.

  • Higher efficiency than Class A.
  • Can suffer from crossover distortion.
  • Used in push-pull power stages.

Class AB

Each output device conducts for slightly more than 180∘180^\circ but less than 360∘360^\circ.

  • Balances efficiency and linearity.
  • Reduces crossover distortion compared with a basic Class B design.
  • Common in audio power amplifiers.

Class C

The active device conducts for less than 180∘180^\circ of each cycle.

  • High efficiency in suitable tuned circuits.
  • Produces substantial distortion without a tuned output network.
  • Used mainly in selected RF applications.

Class D

Uses switching operation, typically with pulse-width modulation or another switching scheme, to control the output.

  • Can achieve high efficiency.
  • Requires output filtering or suitable load characteristics to reconstruct the signal.
  • Common in modern audio power amplifiers.

9. Important Amplifier Characteristics

CharacteristicMeaning
GainHow much the input signal is amplified
BandwidthRange of frequencies amplified effectively
Input impedanceOpposition presented to the input source
Output impedanceEffective impedance seen at the output
DistortionUnwanted change in the signal waveform
NoiseUnwanted electrical signals added by the circuit
EfficiencyRatio of output power to power drawn from the supply

An amplifier's bandwidth is particularly important because gain usually varies with frequency. A circuit designed for audio signals may not work effectively at radio frequencies, and vice versa.

10. Applications of Amplifiers

Заалны Иж Бүрэн Хөгжим Өсгөгч 1300W | ЭЛЕКТРОН ДЭЛГҮҮР

Audio systems

Amplify sound signals to drive speakers and headphones.

AD620 Microvolt/Millivolt Voltage Instrumentation Amplifier Module – QuartzComponents

Sensor circuits

Amplify small signals from temperature, light, pressure, and other sensors before measurement.

Amplificador RF, Amplificador RF Módulo amplificador de potencia PCB de 10 MHz a 500 MHZ Amplificador de potencia El mejor de su clase | Bodega Aurrera en línea

Communication systems

Increase signal strength in radio transmitters and receivers.

PCM1704 DAC 基板

Instrumentation

Condition and amplify signals used by measurement equipment and control systems.

11. Summary

An amplifier increases the voltage, current, or power of an electrical signal using energy from a power supply.

Remember these important formulas:

  • Voltage gain: Av=V_out/V_inA_v=V\_{\text{out}}/V\_{\text{in}}
  • Current gain: Ai=I_out/I_inA_i=I\_{\text{out}}/I\_{\text{in}}
  • Power gain: Ap=P_out/P_inA_p=P\_{\text{out}}/P\_{\text{in}}
  • Voltage gain in decibels: Gv=20log⁡_10∣Av∣G_v=20\log\_{10}|A_v|, when input and output impedances are equal.

Amplifiers are essential components in audio equipment, communication systems, sensor interfaces, and electronic instruments.

Keep learning. Keep building. Keep growing.

© 2026 Ugenz Academy