Ugenz Academy/IoT Tutorial

Filters

6 min read1,148 words

Reading progress

Keep learning

Electronic Filters

1. Introduction

An electronic filter is a circuit that allows certain frequencies of an electrical signal to pass through while reducing or rejecting other frequencies.

Filters are commonly used in audio systems, communication devices, power supplies, radio receivers, and electronic circuits.

For example, a speaker system may use a filter to send low-frequency signals to a subwoofer and high-frequency signals to a tweeter.

Butterworth Filter Design | Tutorials on Electronics | Next Electronics

3-way HiFi Speaker Frequency Divider Tweeter Midrange Woofer Crossover – ELECBEE

Optical Tweezers Apparatus Based on a Cost-Effective IR Laser—Hardware and Software Description

7

2. Why Are Filters Needed?

Electronic signals often contain a mixture of useful signals and unwanted frequencies. Filters help separate them.

The main purposes of filters are:

  • Noise reduction: Reduce unwanted electrical noise.
  • Frequency selection: Select a desired frequency range.
  • Audio processing: Separate bass, midrange, and treble frequencies.
  • Power supply smoothing: Reduce AC ripple in DC power supplies.
  • Communication: Select desired signals and suppress interference.

3. Types of Electronic Filters

Electronic filters are commonly classified by the frequencies they allow to pass.

A. Low-Pass Filter (LPF)

A low-pass filter allows low frequencies to pass while reducing higher frequencies.

Tips on using Frequency Sweep and List with your Function Generator

keysight.com

Applications: Audio bass circuits, sensor signal smoothing, and reducing high-frequency noise.

B. High-Pass Filter (HPF)

A high-pass filter allows high frequencies to pass while reducing lower frequencies.

Understanding High Pass Filters in Electronics: Types, Applications, and Circuit Designs

components101.com

Applications: Removing DC offsets, microphone circuits, and reducing low-frequency rumble.

C. Band-Pass Filter (BPF)

A band-pass filter allows a particular range of frequencies to pass while reducing frequencies below and above that range.

File:Bandwidth.svg - Wikimedia Commons

commons.wikimedia.org

Applications: Radio receivers, wireless communication, and audio equalizers.

D. Band-Stop Filter (BSF)

A band-stop filter reduces a particular range of frequencies while allowing frequencies outside that range to pass. It is also called a band-reject filter.

Complete Guide to Bandstop Filter

allelcoelec.com

Applications: Removing unwanted interference, such as 50 Hz or 60 Hz mains hum, when a suitable notch filter is designed.

4. Passive and Active Filters

Electronic filters can also be classified according to the components used to build them.

A. Passive Filters

A passive filter uses resistors, capacitors, and inductors without requiring an active amplification component.

uciradiuzivaj | elektrotehnika

uciradiuzivaj.com.ba

Characteristics:

  • Uses passive components such as R, L, and C.
  • Does not provide power gain.
  • Usually simple and inexpensive.
  • Common in basic audio circuits and power supplies.

B. Active Filters

An active filter uses active components, such as operational amplifiers (op-amps), together with resistors and capacitors.

Filtre actif passe bas/Fonction de transfert — Wikiversité

fr.wikiversity.org

Characteristics:

  • Can provide voltage gain.
  • Can offer high input impedance and low output impedance.
  • Can be designed without inductors.
  • Requires a suitable power supply for its active components.
FeaturePassive filterActive filter
Main componentsR, L, COp-amp, R, C
AmplificationNo power gainCan provide gain
Power supplyUsually not required separatelyRequired for active components
InductorsMay be usedOften avoidable
ComplexityUsually simplerUsually more complex

5. RC Filter Circuits

An RC filter uses a resistor and capacitor to control the frequency response of a signal.

A. RC Low-Pass Filter

A basic RC low-pass filter has a resistor connected in series with the input and a capacitor connected from the output node to ground. The output is taken across the capacitor.

Simplified RC low-pass filter; output is measured across the capacitor.

Working principle:

  • At low frequencies, the capacitor has high reactance, so most of the input voltage appears across it.
  • At high frequencies, the capacitor has low reactance, so more of the signal is diverted to ground.
  • Therefore, low frequencies pass more easily than high frequencies.

B. RC High-Pass Filter

A basic RC high-pass filter has a capacitor in series with the input and a resistor connected from the output node to ground. The output is taken across the resistor.

Simplified RC high-pass filter; output is measured across the resistor.

Working principle:

  • At low frequencies, the capacitor strongly opposes current, so the output is small.
  • At high frequencies, the capacitor offers less reactance, allowing more signal to appear across the resistor.
  • Therefore, high frequencies pass more easily than low frequencies.

6. Cutoff Frequency

The cutoff frequency is the frequency at which a first-order filter's output magnitude falls to approximately 70.7% of its passband value. This corresponds to the −3 dB point.

For a basic RC low-pass or high-pass filter:

fc=12πRC\boxed{f_c=\frac{1}{2\pi RC}}

Where:

  • fcf_c = cutoff frequency in hertz (Hz)
  • RR = resistance in ohms (Ω\Omega)
  • CC = capacitance in farads (F)

Example

Suppose:

  • R=1,kΩ=1000,ΩR=1\\,k\Omega=1000\\,\Omega
  • C=0.1,μF=0.1×10−6,FC=0.1\\,\mu F=0.1\times10^{-6}\\,F

Substitute into the formula:

fc=12π(1000)(0.1×10−6)f_c=\frac{1}{2\pi(1000)(0.1\times10^{-6})} fc≈1591.5 Hz\boxed{f_c\approx1591.5\text{ Hz}}

The cutoff frequency is approximately 1.59 kHz.

For a first-order low-pass filter, frequencies below this point pass with less attenuation, while higher frequencies are increasingly reduced. A first-order filter rolls off at approximately 20 dB per decade beyond the cutoff frequency.

7. Filter Response and Gain

Filter response describes how much the circuit changes a signal's amplitude at different frequencies.

The voltage gain magnitude is

∣H(f)∣=∣V_outV_in∣|H(f)|=\left|\frac{V\_{\text{out}}}{V\_{\text{in}}}\right|

For a first-order RC low-pass filter:

∣H(f)∣=11+(f/fc)2|H(f)|=\frac{1}{\sqrt{1+(f/f_c)^2}}

For a first-order RC high-pass filter:

∣H(f)∣=f/fc1+(f/fc)2|H(f)|=\frac{f/f_c}{\sqrt{1+(f/f_c)^2}}

At the cutoff frequency, both have a gain magnitude of approximately 0.7070.707 relative to their passband gain.

8. Applications of Electronic Filters

DENX Sub Filter

Audio systems

Separate bass, midrange, and treble signals for different speakers.

load - Calculating the ripple voltage from a standard wall adapter power supply - Electrical Engineering Stack Exchange

Power supplies

Reduce unwanted ripple and noise in rectified DC voltage.

Band Pass Filter

Communication systems

Select desired frequency bands and reduce interference.

Silicon Labs Community

Sensors and microcontrollers

Reduce high-frequency noise before signals are measured by an ADC.

9. Summary

An electronic filter controls which frequencies pass through a circuit.

FilterFrequencies passedFrequencies reduced
Low-passLow frequenciesHigh frequencies
High-passHigh frequenciesLow frequencies
Band-passA selected frequency rangeFrequencies outside that range
Band-stopFrequencies outside a selected rangeA selected frequency range

Filters can be passive or active. RC filters are particularly useful in basic electronic circuits because they are simple to design and use.

The key formula for a first-order RC filter is:

fc=12πRC\boxed{f_c=\frac{1}{2\pi RC}}

Keep learning. Keep building. Keep growing.

© 2026 Ugenz Academy