Ugenz Academy/IoT Tutorial

Feedback Circuits

5 min read951 words

Reading progress

Keep learning

Feedback Circuits in Electronics

1. Introduction

A feedback circuit is an electronic circuit in which a portion of the output signal is returned to the input.

Feedback is used to control an amplifier's gain, improve stability, reduce distortion, control oscillation, and influence the frequency response of a circuit.

Feedback circuits are commonly used in amplifiers, oscillators, voltage regulators, operational amplifiers, and automatic control systems.

Negative Feedback Amplifier Circuit Diagram Negative Feedbac

Basic Circuit Diagrams Solution | ConceptDraw.com

Relay Using Breadboard at Norma Castro blog

9

For example, an operational amplifier can use feedback resistors to set a predictable voltage gain instead of relying on its extremely high internal gain.

2. Basic Working Principle

A feedback system typically contains:

  1. Input signal: The signal supplied to the circuit.
  2. Amplifier or control system: Processes the input signal.
  3. Output signal: The resulting signal produced by the system.
  4. Feedback network: Returns a portion of the output to the input.

Conceptual feedback diagram. The feedback signal combines with the input at the summing point.

The output is sampled, a portion is returned through the feedback network, and the returned signal combines with the original input. The result depends on whether the feedback reinforces or opposes the input.

3. Types of Feedback

There are two main types of feedback in electronic circuits:

  • Positive feedback
  • Negative feedback

A. Positive Feedback

Positive feedback occurs when the feedback signal reinforces the input signal.

The feedback signal effectively adds to the input, which can increase the overall response.

Characteristics:

  • Reinforces the input signal.
  • Can cause a circuit to switch rapidly between states.
  • Can produce sustained oscillations when the required gain and phase conditions are met.
  • Can make a system unstable if not properly controlled.

Applications:

  • Oscillators
  • Schmitt triggers
  • Regenerative circuits
  • Certain switching circuits

For example, positive feedback helps a Schmitt trigger switch cleanly between high and low output states.

B. Negative Feedback

Negative feedback occurs when the feedback signal opposes the input signal.

It reduces the difference between the original input and the returned feedback signal, helping control the circuit's output.

Characteristics:

  • Reduces overall gain compared with the same amplifier without feedback.
  • Improves gain stability.
  • Usually reduces distortion and unwanted noise generated within the amplifier.
  • Can increase bandwidth.
  • Can improve linearity and make the output more predictable.

Applications:

  • Audio amplifiers
  • Operational amplifier circuits
  • Voltage regulators
  • Signal-conditioning circuits

4. Difference Between Positive and Negative Feedback

FeaturePositive feedbackNegative feedback
EffectReinforces the inputOpposes the input
GainCan increase greatly near instabilityUsually reduces gain
StabilityCan cause instabilityOften improves stability
DistortionMay increase nonlinear behaviorUsually reduces distortion
BandwidthDepends on circuit designOften increases bandwidth
Common applicationOscillators, Schmitt triggersAmplifiers, regulators

5. Negative Feedback in an Amplifier

Consider an amplifier with an open-loop gain AA and a feedback factor β\beta.

For a standard negative-feedback amplifier, the closed-loop gain is

Af=A1+Aβ\boxed{A_f=\frac{A}{1+A\beta}}

Where:

  • AfA_f = gain with feedback
  • AA = gain without feedback
  • β\beta = fraction of the output returned to the input
  • AβA\beta = loop gain

Example

Suppose an amplifier has:

  • Open-loop gain A=100A=100
  • Feedback factor β=0.1\beta=0.1

Then:

Af=1001+(100)(0.1)A_f=\frac{100}{1+(100)(0.1)} Af=10011A_f=\frac{100}{11} Af≈9.09\boxed{A_f\approx9.09}

The gain decreases from 100 to approximately 9.09, but it becomes more controlled and less sensitive to variations in the amplifier's internal gain.

6. Feedback in an Operational Amplifier

Operational amplifiers (op-amps) commonly use negative feedback to establish a predictable gain.

Basic Circuit Diagrams Solution | ConceptDraw.com

conceptdraw.com

For a standard non-inverting op-amp amplifier:

Av=1+RfR1\boxed{A_v=1+\frac{R_f}{R_1}}

Where:

  • RfR_f = feedback resistor connected from output to the inverting input
  • R1R_1 = resistor connected between the inverting input and ground
  • AvA_v = ideal closed-loop voltage gain

For example, if Rf=9,kΩR_f=9\\,k\Omega and R1=1,kΩR_1=1\\,k\Omega:

Av=1+90001000A_v=1+\frac{9000}{1000} Av=10\boxed{A_v=10}

With a 0.2 V0.2\text{ V} input, the ideal output is 2 V2\text{ V}, provided the op-amp's supply voltage and output limits permit it.

7. Feedback in Oscillators

Oscillators use feedback to generate repeating signals.

  • Positive feedback helps sustain the oscillation when the loop gain and phase meet the required conditions.
  • A frequency-selective network determines the desired oscillation frequency.
  • The circuit's nonlinear behavior or amplitude-control mechanism prevents the output from growing indefinitely.

Examples include RC phase-shift oscillators, LC oscillators, and crystal oscillators.

8. Applications of Feedback Circuits

Probleme beim Audioverstärker-IC LM4780 - Mikrocontroller.net

Audio amplifiers

Negative feedback helps control gain and reduce distortion.

Automatic voltage regulator - EA448B - Kutai Electronics Industry Co., Ltd.

Voltage regulators

Feedback compares the output with a reference and adjusts the circuit to maintain the desired voltage.

What is a Clock Oscillator? | Technical information | Electronic Components & Devices | KYOCERA

Oscillators

Positive feedback sustains periodic electrical signals.

Band pass filter sallen key - CircuitLab

Active filters

Feedback helps establish the filter's gain, frequency response, and selectivity.

9. Summary

A feedback circuit returns part of its output to its input to influence how the system operates.

The two main types are:

  • Positive feedback: Reinforces the input; commonly used in oscillators and switching circuits.
  • Negative feedback: Opposes the input; commonly used to stabilize amplifier gain and reduce distortion.

The key negative-feedback gain formula is

Af=A1+Aβ\boxed{A_f=\frac{A}{1+A\beta}}

Feedback is essential in modern electronics because it allows circuits to control gain, improve performance, and produce predictable outputs.

Keep learning. Keep building. Keep growing.

© 2026 Ugenz Academy