Ugenz Academy/IoT Tutorial

Breadboard Circuits

9 min read1,625 words

Reading progress

Keep learning

Breadboard Circuits

1. What Is a Breadboard?

A breadboard is a reusable electronic board used to build and test electronic circuits without soldering. It allows you to connect components such as resistors, LEDs, switches, sensors, and integrated circuits using jumper wires.

Breadboards are especially useful for learning electronics, testing circuit designs, and developing projects with Arduino, ESP32, and other microcontrollers.

electronics

Arduino Arcade | Tufts Maker Network

How to Build Your 1st Circuit : 20 Steps (with Pictures) - Instructables

12

Main advantages

  • No soldering required: Components can be inserted and removed easily.
  • Reusable: The same breadboard can be used for many circuits.
  • Easy troubleshooting: Connections can be changed quickly.
  • Low cost: It is useful for experimenting before making a permanent PCB.
  • Beginner-friendly: It helps learners understand how electronic components connect.

A breadboard is primarily intended for prototyping. It is not suitable for every circuit, especially circuits involving high current, high voltage, or very high frequencies.

2. Parts of a Breadboard

A typical solderless breadboard has three main areas: the terminal strips, power rails, and center gap.

KS0536/KS0537 Keyestudio Ultimate Starter Kit for Arduino — keyestudio WiKi documentation

docs.keyestudio.com

A. Terminal strips

The terminal strips are the main working area where you insert components and jumper wires.

On a common breadboard, the holes are arranged in groups of five. The five holes in each group are electrically connected internally.

For example, on a standard breadboard with rows labeled A–E and F–J, holes A1, B1, C1, D1, and E1 share an electrical connection.

However, A1 and A2 are not connected to each other.

B. Power rails

Power rails are long rows of holes usually marked with red + and blue or black − lines.

They are commonly used to distribute power throughout the circuit.

  • Positive rail (+): Connects to the positive supply, such as 3.3 V or 5 V.
  • Negative rail (−): Often connects to ground (GND).

Power rails are not automatically connected to a power source. You must connect the supply yourself.

Also, some breadboards have power rails that are split into separate sections. Always check their internal connections before relying on them.

C. Center gap

The center gap separates the two terminal-strip sections. It allows dual-inline package (DIP) integrated circuits to be inserted without connecting their pins together across the same terminal group.

For example, a 555 timer IC can be placed across the center gap so that its pins on opposite sides remain electrically separate.

3. How Breadboard Connections Work

The most important thing to understand about a breadboard is its internal electrical connections.

Typical terminal-strip connection

Simplified illustration of the common five-hole connection pattern.

On a typical breadboard:

  • Holes A1–E1 are connected together.
  • Holes A2–E2 form another connected group.
  • Holes F1–J1 form a separate group across the center gap.
  • Holes A1 and F1 are not connected.

This means two component leads inserted into the same connected group share the same electrical node.

Important: Breadboard hole layouts can vary. Check the manufacturer's diagram for your specific board.

4. How to Build a Circuit on a Breadboard

Follow these steps when assembling a basic circuit.

Step 1: Plan the circuit

Draw or review the circuit diagram before inserting components. Identify the power supply, ground, and connections between components.

Step 2: Connect the power rails

Connect the positive supply to the positive rail and ground to the negative rail. Make sure the supply voltage matches your components.

Basit LED Devresi - Devre Projeleri - Elektronik Atölyesi

Step 3: Insert components

Place resistors, LEDs, switches, and other components in the correct holes. Keep component leads in separate electrical groups whenever required by the circuit.

AVR: Interrupções - Parte 1 - Microcontrolandos

Step 4: Add jumper wires

Use jumper wires to connect different rows and components according to the circuit diagram.

How to Use a Multimeter - SparkFun Learn

Step 5: Check and test

Check for misplaced wires, reversed polarity, and short circuits before applying power. Use a multimeter when necessary.

5. Example 1: LED Circuit on a Breadboard

An LED circuit is one of the simplest ways to understand breadboard connections.

How to Use a Breadboard

sciencebuddies.org

Components required

ComponentQuantity
Solderless breadboard1
LED1
Resistor, 330 Ω1
5 V DC supply1
Jumper wiresAs needed

Circuit diagram

Connections

  1. Connect the positive 5 V supply to one end of the 330 Ω resistor.
  2. Connect the other end of the resistor to the LED's anode (positive side).
  3. Connect the LED's cathode (negative side) to ground.
  4. Apply power after checking the connections.

The resistor limits the current flowing through the LED and helps prevent damage.

Calculating the LED current

Ohm's law is:

I=VRI=\frac{V}{R}

Assume the supply is 5 V and the red LED has a forward voltage of 2 V.

I=5−2330I=\frac{5-2}{330} I≈0.0091 A=9.1 mAI\approx0.0091\text{ A}=9.1\text{ mA}

The approximate current is 9.1 mA, which is suitable for many standard indicator LEDs.

6. Example 2: Push Button and LED Circuit

A push button can control whether current flows through an LED.

An Introduction to Circuit Design With Fritzing | Custom | Maker Pro

maker.pro

Components required

  • Breadboard
  • LED
  • 330 Ω resistor
  • Normally open push button
  • 5 V DC supply
  • Jumper wires

Working principle

When the push button is not pressed, its contacts remain open and the circuit is incomplete. The LED remains off.

When the button is pressed, its contacts close, completing the circuit and allowing current to flow through the LED.

A typical connection is:

5 V → push button → resistor → LED → GND

The resistor and LED may be placed in the opposite order in the series path; their current remains the same.

Many four-pin tactile push buttons have pairs of pins that are already connected internally. Position the button across the breadboard's center gap when appropriate, and verify its pin arrangement.

7. Example 3: Connecting an Arduino or ESP32

Breadboards are widely used with microcontrollers because they make it easy to connect sensors, LEDs, buttons, displays, and other electronic modules.

Leds On Arduino Uno at Melinda Hawthorne blog

ESP32 IOT Dashboard. | ESP32

Project-08 : Web Server - My Logs

11

Example: ESP32 controlling an LED

A basic LED can be connected between a GPIO pin and ground through a current-limiting resistor.

ESP32 connectionBreadboard circuit
GPIO 23330 Ω resistor
Other resistor endLED anode
LED cathodeGND
ESP32 GNDBreadboard ground rail, if used

When the GPIO is configured as an output, setting it HIGH can turn the LED on, and setting it LOW can turn it off.

For an ESP32, use 3.3 V-compatible connections on its GPIO pins. Never apply 5 V directly to a standard ESP32 GPIO pin. The breadboard itself does not reduce voltage or protect the microcontroller.

8. Breadboard vs. Soldered Circuit

PTTAVM: Orta Boy Breadboard 400 Pin Hücre Protoboard Prototip Deney

Breadboard circuit

  • Reusable and easy to modify
  • No soldering required
  • Ideal for experiments and testing
  • Connections can become loose

小山工業高等専門学校 教育研究技術支援部 技術室 - ユニバーサル基板はんだ付け講座 第2回

Soldered circuit

  • More permanent connections
  • Better suited to finished prototypes
  • Requires soldering tools and skills
  • Changes are more difficult

A breadboard is generally best for testing a circuit before transferring the design to a perfboard or printed circuit board (PCB).

9. Common Breadboard Mistakes

MistakeResult or solution
Placing both LED leads in the same connected groupThe LED may be bypassed or fail to work as intended.
Forgetting the ground connectionThe circuit may remain incomplete.
Connecting power to the wrong railComponents may receive incorrect polarity.
Assuming all power rails are continuousA split rail can leave part of the circuit unpowered.
Forgetting the LED resistorExcessive current may damage the LED or output pin.
Using loose or incorrectly placed jumper wiresIntermittent or missing connections.
Applying the wrong voltageComponents may overheat or be damaged.
Building with power connectedAccidental shorts can damage components or the supply.

10. Important Breadboard Safety and Limitations

  • Use low-voltage DC supplies appropriate for the circuit.
  • Disconnect power before rearranging wires or components.
  • Avoid mains electricity, such as 120 V or 230 V AC, on a solderless breadboard.
  • Check the current limits of the breadboard, wires, components, and power supply.
  • Keep wiring short and organized, especially for sensitive or high-frequency circuits.
  • Use a multimeter's continuity mode to verify uncertain connections, with the circuit powered off.

11. Summary of Breadboard Circuits

A breadboard is a reusable platform for building electronic circuits without soldering. Its internal metal strips connect specific groups of holes, allowing components to share electrical connections.

The key concepts are:

  • Terminal strips connect components in groups.
  • Power rails distribute supply voltage and ground when wired correctly.
  • The center gap separates the two terminal-strip sections and accommodates DIP ICs.
  • Jumper wires connect electrical nodes.
  • Resistors and correct power connections help protect components.

Once you understand the breadboard's internal connections, you can use it to build circuits ranging from simple LEDs and switches to Arduino, ESP32, and sensor-based projects.

Keep learning. Keep building. Keep growing.

© 2026 Ugenz Academy