Ugenz Academy/IoT Tutorial

Voltage And Current Measurement

10 min read1,953 words

Reading progress

Keep learning

Voltage and Current Measurement in Electronics

1. Introduction

Voltage and current measurement are two of the most important tasks in electronics. They help determine whether a circuit is receiving the correct electrical supply and whether components are operating properly.

A voltmeter measures voltage, while an ammeter measures electric current. A digital multimeter (DMM) can measure both quantities, making it one of the most useful instruments for electronics students, technicians, and engineers.

For example, when working with an ESP32, Arduino, sensors, batteries, or power supplies, voltage and current measurements help identify wiring mistakes, power problems, and excessive current consumption.

2. What Is Voltage?

Voltage is the electrical potential difference between two points in a circuit. It provides the potential that drives electric charge through a conducting path.

Voltage is measured in volts (V).

The symbol for voltage is VV.

Formula

V=WQV=\frac{W}{Q}

Where:

  • VV = voltage in volts
  • WW = electrical work or energy transferred in joules
  • QQ = electric charge in coulombs

Example

If 12 joules of energy are transferred for every 2 coulombs of charge, the voltage is:

V=122=6,VV=\frac{12}{2}=6\\,V

Therefore, the potential difference is 6 volts.

Common Voltage Levels

Device or circuitTypical voltage
Coin-cell battery3 V
ESP32 GPIO logic3.3 V
Arduino Uno GPIO logic5 V
USB supply5 V
Common small battery9 V
Automotive battery (nominal)12 V
Household supply in NepalApproximately 230 V AC

These are typical or nominal values. Actual readings depend on the device, operating conditions, and supply specifications.

3. What Is Electric Current?

Electric current is the rate at which electric charge flows through a conductor or circuit.

Current is measured in amperes (A), commonly called amps.

The symbol for current is II.

Formula

I=QtI=\frac{Q}{t}

Where:

  • II = current in amperes
  • QQ = electric charge in coulombs
  • tt = time in seconds

Example

If 10 coulombs of charge pass through a conductor in 5 seconds:

I=105=2,AI=\frac{10}{5}=2\\,A

Therefore, the current is 2 amperes.

Common Current Levels

Device or componentExample current
Low-power sensorA few mA
Indicator LEDOften 5–20 mA
Small electronic moduleTens to hundreds of mA
Small DC motorHundreds of mA or more
USB-powered deviceDepends on the USB supply and device

Actual current varies considerably with the component and its operating conditions.

4. Difference Between Voltage and Current

Voltage and current are related, but they describe different electrical quantities.

FeatureVoltageCurrent
MeaningElectrical potential differenceRate of charge flow
SymbolVVII
UnitVolt (V)Ampere (A)
InstrumentVoltmeterAmmeter
ConnectionParallelSeries
Main questionWhat potential difference exists?How much current flows?

Water Flow Analogy

Imagine water flowing through a pipe:

  • Voltage is similar to the pressure difference that drives water.
  • Current is similar to the amount of water flowing per second.
  • Resistance is similar to an obstruction that restricts flow.

This analogy helps explain the relationship, although electrical circuits behave differently from water systems in several important ways.

5. Instruments Used for Measurement

Multimeter Dixhital - Buzi Store

5.1 Digital Multimeter (DMM)

A digital multimeter measures voltage, current, resistance, and often continuity. Some models also measure capacitance, frequency, temperature, and other quantities.

Digital Bench Voltmeter – Arbor Scientific

5.2 Voltmeter

A voltmeter measures the potential difference between two points. It is connected in parallel with the component or supply being measured.

Digital Bench Ammeter – Arbor Scientific

5.3 Ammeter

An ammeter measures current flowing through a circuit branch. It is connected in series with the branch being tested.

Comment mesurer le courant sans couper le circuit

5.4 Clamp Meter

A clamp meter measures current by sensing the magnetic field around a conductor. Many models can measure AC current, and some can measure DC current as well. It can often measure current without disconnecting the conductor.

6. Measuring Voltage with a Digital Multimeter

Voltage is measured by placing the meter's probes across two points.

TASI TA800A Digital Multimeter User Manual

manuals.plus

Steps

  1. Insert the black probe into the COM terminal.
  2. Insert the red probe into the voltage terminal, usually marked V or VΩ.
  3. Select DC voltage (V⎓) for batteries and DC circuits.
  4. Select AC voltage (V~) for AC supplies.
  5. Place the probes across the two points being measured.
  6. Read the displayed voltage.

For DC measurements, connecting red to the more positive point and black to the more negative point normally gives a positive reading. Reversing the probes may show a negative sign.

Example: Measuring a 9 V Battery

Suppose a battery is expected to provide approximately 9 V.

The meter displays:

V=8.7,VV=8.7\\,V

The measured terminal voltage is 8.7 V. Whether this is acceptable depends on the battery chemistry, condition, and load.

Important: A battery's measured voltage alone does not establish its remaining capacity or ability to supply a particular current.

7. Measuring Current with a Digital Multimeter

Current measurement is different from voltage measurement. The meter must be placed in series with the branch whose current is being measured.

Circuit Basics Physics 10300 Experiment 6

physicslabs.ccnysites.cuny.edu

Steps

  1. Turn off the circuit power.
  2. Insert the black probe into COM.
  3. Move the red probe to the correct current input, such as mA or A, according to the expected current and meter instructions.
  4. Select DC current (A⎓) or AC current (A~) as appropriate.
  5. Open the circuit at the point where current will be measured.
  6. Connect the meter in series so the circuit current flows through it.
  7. Power the circuit and read the result, observing the meter's limits.
  8. Turn off the circuit before removing the meter and restoring the original connection.

Start with a suitable higher current range if the expected current is unknown and the meter supports manual ranging.

Critical safety rule: Never connect a multimeter configured for current measurement directly across a battery or voltage source. This can create a short circuit, blow the meter's fuse, damage equipment, or cause burns.

8. Understanding AC and DC Measurements

Voltage and current can be either direct or alternating.

AC vs DC: Key Differences, Examples & Applications

8.1 Direct Current (DC)

DC flows in one direction in a circuit. Its voltage may be steady or may vary over time while retaining the same polarity.

Examples: batteries, USB supplies, and many microcontroller power circuits.

Dòng điện xoay chiều (AC): Khái niệm, đặc điểm và ứng dụng

8.2 Alternating Current (AC)

AC changes direction periodically. AC voltage and current measurements are often expressed as RMS values, depending on the meter and waveform.

Examples: household electricity and AC generator output.

MeasurementMultimeter setting
Battery voltageDC voltage (V⎓)
USB supply voltageDC voltage (V⎓)
Household outlet voltageAC voltage (V~)
DC circuit currentDC current (A⎓)
AC circuit currentAC current (A~)

Household mains voltage is dangerous. Only use a properly rated meter and leads, and only perform mains measurements if trained to do so. Never probe exposed live conductors without appropriate safety procedures.

9. Relationship Between Voltage, Current, and Resistance

Voltage, current, and resistance are related through Ohm's law for an ohmic component under suitable conditions.

V=IRV=I R

Where:

  • VV = voltage in volts
  • II = current in amperes
  • RR = resistance in ohms (Ω\Omega)

The formula can be rearranged:

I=VRI=\frac{V}{R} R=VIR=\frac{V}{I}

Example

A 100 Ω\Omega resistor is connected across a 5 V supply.

I=5100=0.05,AI=\frac{5}{100}=0.05\\,A

Converting amperes to milliamperes:

I=0.05×1000=50,mAI=0.05\times1000=50\\,mA

The expected current is 50 mA, assuming an ideal 5 V supply and a 100 Ω\Omega resistor.

10. Measuring Electrical Power

Voltage and current measurements can also be used to calculate electrical power.

For a DC circuit, or a suitable resistive load:

P=VIP=VI

Where:

  • PP = power in watts (W)
  • VV = voltage in volts
  • II = current in amperes

Example

A device operates at 5 V and draws 0.4 A.

P=5×0.4=2,WP=5\times0.4=2\\,W

The device consumes 2 W of electrical power under those conditions.

For AC circuits with phase differences or distorted waveforms, real power may require additional information or a suitable power meter.

11. Common Measurement Errors

ErrorPossible consequence
Measuring voltage in current modeMay short the supply through the meter
Measuring current in parallelMay cause a short circuit
Using the wrong input terminalIncorrect readings or blown fuse
Selecting AC mode for a DC measurementIncorrect or misleading reading
Choosing an unsuitable rangeOver-range display or poor resolution
Loose probe contactUnstable readings
Ignoring probe polarityNegative DC reading
Measuring resistance in a powered circuitIncorrect readings and possible meter damage

12. Applications in Electronics

Voltage and current measurement are essential for:

  1. Battery testing: Checking battery terminal voltage.
  2. Power supply testing: Verifying that a supply produces the expected output.
  3. Arduino and ESP32 projects: Checking supply rails and circuit current consumption.
  4. Sensor troubleshooting: Confirming supply voltage and output behavior.
  5. LED circuits: Checking voltage drops and operating current.
  6. Motor circuits: Measuring supply voltage and current draw within the meter's rating.
  7. PCB troubleshooting: Identifying missing supply voltages or unexpected current consumption.
  8. Solar and IoT systems: Monitoring panel voltage, battery voltage, and load current.

13. Practical Example: Measuring an LED Circuit

Suppose an LED is connected to a 5 V supply through a 220 Ω\Omega resistor. Assume the LED forward voltage is 2 V.

The resistor voltage is:

VR=5−2=3,VV_R=5-2=3\\,V

Using Ohm's law:

I=VRRI=\frac{V_R}{R} I=3220≈0.0136,AI=\frac{3}{220}\approx0.0136\\,A

Therefore:

I≈13.6,mAI\approx13.6\\,mA

A multimeter can verify the voltage across the resistor and measure the current by being inserted in series. The actual values may differ due to the LED's forward voltage, resistor tolerance, and supply variation.

14. Safety Precautions

  • Inspect the multimeter, probes, and insulation before use.
  • Confirm the correct mode, terminal, and measurement category.
  • Never measure resistance or continuity on an energized circuit.
  • Never connect a current-input meter directly across a voltage source.
  • Observe the meter's maximum voltage, current, and input-fuse ratings.
  • Use extra caution with capacitors, batteries capable of high fault currents, and inductive loads.
  • Do not perform household mains measurements unless trained and equipped for them.
  • After current measurement, return the red lead to the voltage terminal before measuring voltage.

15. Summary

Voltage measures electrical potential difference, while current measures the rate of electric charge flow. A digital multimeter can measure both quantities when the correct mode, input terminal, and connection method are used.

Voltage is measured in parallel, whereas current is measured in series. Understanding these differences, applying Ohm's law, and following safety precautions are essential skills for testing and troubleshooting electronic circuits, including Arduino, ESP32, and other IoT projects.

Keep learning. Keep building. Keep growing.

© 2026 Ugenz Academy