Ugenz Academy/IoT Tutorial

Resistance Measurement

9 min read1,633 words

Reading progress

Keep learning

Resistance Measurement in Electronics

1. Introduction

Resistance measurement is the process of determining how much a material or electronic component opposes the flow of electric current.

Resistance is one of the fundamental properties of electrical and electronic circuits. Measuring resistance helps identify faulty components, check resistor values, test wires, and troubleshoot electronic devices.

Resistance is measured using an instrument such as a digital multimeter (DMM) and is expressed in ohms (Ω\Omega).

For example, when building an Arduino or ESP32 circuit, you can measure a resistor to confirm whether it has the correct value before connecting it to an LED or sensor circuit.

2. What Is Electrical Resistance?

Electrical resistance is the opposition that a material or component provides to electric current.

The symbol for resistance is RR, and its SI unit is the ohm, represented by Ω\Omega.

According to Ohm's law:

R=VIR=\frac{V}{I}

Where:

  • RR = resistance in ohms (Ω\Omega)
  • VV = voltage across the component in volts (V)
  • II = current through the component in amperes (A)

Example

Suppose a resistor has 10 V across it and carries 2 A of current.

R=102=5,ΩR=\frac{10}{2}=5\\,\Omega

Therefore, the resistance is 5,Ω5\\,\Omega.

This calculation applies when the component follows Ohm's law under the given operating conditions.

3. Units of Resistance

Resistance can range from fractions of an ohm to millions of ohms.

UnitSymbolEquivalent
MilliohmmΩ0.001,Ω0.001\\,\Omega
OhmΩ1,Ω1\\,\Omega
KilohmkΩ1,000,Ω1,000\\,\Omega
MegohmMΩ1,000,000,Ω1,000,000\\,\Omega

Examples

  • 220,Ω220\\,\Omega = 220 ohms
  • 4.7,kΩ4.7\\,k\Omega = 4,700 ohms
  • 1,MΩ1\\,M\Omega = 1,000,000 ohms

Resistance values are commonly printed on resistors using numerical markings or color bands.

4. Instrument Used for Resistance Measurement

Измеряем сопротивление резистора мультиметром вместе с Суперайс

Resistansmåling med multimeter - Energi- og styresystemer (EL-ELE vg1) - NDLA

Multimetro tutorial come utilizzare un tester - PROGETTI ARDUINO

9

The most common instrument used to measure resistance is a digital multimeter.

Other instruments include:

  • Ohmmeter: Designed specifically to measure resistance.
  • LCR meter: Measures inductance, capacitance, and resistance.
  • Four-wire resistance meter: Provides more accurate measurements of very low resistance by reducing the influence of test-lead resistance.

A digital multimeter is usually sufficient for testing common electronic components and wiring.

5. How Does Resistance Measurement Work?

A multimeter measures resistance by applying a small internal test voltage or current to the component and measuring the resulting electrical response.

The instrument then calculates and displays the resistance.

R=V_testI_testR=\frac{V\_{\text{test}}}{I\_{\text{test}}}

Here, V_testV\_{\text{test}} and I_testI\_{\text{test}} represent the meter's internal test voltage and current.

Important: Resistance must generally be measured with the circuit switched off and the component isolated from external power. Otherwise, external voltage can cause incorrect readings or damage the meter.

6. How to Measure Resistance Using a Digital Multimeter

Cómo usar un multímetro: consejos para realizar mediciones profesionales - Blog

jucarsa.es

Follow these steps to measure the resistance of a resistor.

  1. Switch off the circuit's power supply.
  2. Disconnect the component from the circuit if necessary. For accurate measurements, lifting one resistor lead can prevent parallel paths from affecting the result.
  3. Insert the black probe into the COM terminal.
  4. Insert the red probe into the VΩ terminal.
  5. Select resistance mode, marked with the Ω\Omega symbol.
  6. Choose an appropriate range if the meter does not select it automatically.
  7. Place one probe on each terminal of the resistor.
  8. Read the resistance displayed on the screen.

For an ordinary resistor, reversing the probes usually does not change the reading.

Example

Suppose you measure a resistor labeled 1,kΩ1\\,k\Omega.

The multimeter displays:

R=0.98,kΩR=0.98\\,k\Omega

Converting to ohms:

R=0.98×1000=980,ΩR=0.98\times1000=980\\,\Omega

The measured resistance is 980,Ω980\\,\Omega. Whether this is acceptable depends on the resistor's tolerance.

7. Understanding Multimeter Resistance Readings

Display or readingPossible meaning
0.0,Ω0.0\\,\Omega or a value near zeroVery low resistance; check for a short or direct connection
10,Ω10\\,\OmegaA low-resistance path
1.0,kΩ1.0\\,k\OmegaResistance of 1,000 ohms
100,kΩ100\\,k\OmegaResistance of 100,000 ohms
OLOver-range or an open circuit, depending on the meter and test conditions
Unstable readingPoor probe contact, changing component behavior, or circuit effects

A reading close to zero does not automatically mean a component is faulty. For example, a wire is expected to have very low resistance.

Similarly, OL can indicate an open component, but it can also mean that the resistance exceeds the selected range.

8. Measuring Different Types of Resistors

Resistors are available in different resistance values and power ratings.

전자부품 저항의 종류 및 특징

8.1 Fixed Resistors

Fixed resistors have a specified nominal resistance, such as 220,Ω220\\,\Omega, 1,kΩ1\\,k\Omega, or 10,kΩ10\\,k\Omega. Measure them with the circuit de-energized.

10pcs 10K Ohm Potentiometer Single Linear – Electronic Pro

8.2 Potentiometers

A potentiometer is an adjustable resistor. Measuring between its two outer terminals generally gives the total resistance, while measuring between the middle terminal and an outer terminal gives a resistance that changes as the shaft turns.

LDR Photo Resistors Light 5mm GL5516

8.3 Light-Dependent Resistors (LDRs)

An LDR changes resistance depending on light intensity. Its resistance generally decreases as light intensity increases.

060421-5 - THERMISTOR NTC DISC/BEAD D=??mm P=??mm 22K 1%

8.4 Thermistors

Thermistors change resistance with temperature. An NTC thermistor generally decreases in resistance as temperature increases, while a PTC thermistor generally increases in resistance over its specified operating region.

9. Resistor Tolerance

Resistor tolerance describes how far the actual resistance may vary from its nominal value under specified conditions.

For example, a 1,kΩ1\\,k\Omega resistor with a tolerance of ±5%\pm5\% may have an acceptable resistance range of:

R_min⁡=1000−(0.05×1000)R\_{\min}=1000-(0.05\times1000) R_min⁡=950,ΩR\_{\min}=950\\,\Omega

Similarly:

R_max⁡=1000+(0.05×1000)R\_{\max}=1000+(0.05\times1000) R_max⁡=1050,ΩR\_{\max}=1050\\,\Omega

Therefore, the acceptable nominal range is:

950,Ω≤R≤1050,Ω950\\,\Omega\leq R\leq1050\\,\Omega

A measured value of 980,Ω980\\,\Omega is within this range.

10. Resistance Measurement in Series and Parallel Circuits

Resistance measurement is useful for understanding how resistors combine in a circuit.

10.1 Series Resistance

When resistors are connected in series, their equivalent resistance is the sum of their individual resistances.

RT=R1+R2+R3R_T=R_1+R_2+R_3

Example:

Two resistors of 100,Ω100\\,\Omega and 220,Ω220\\,\Omega are connected in series.

RT=100+220=320,ΩR_T=100+220=320\\,\Omega

The total resistance is 320,Ω320\\,\Omega.

10.2 Parallel Resistance

For two resistors connected in parallel:

RT=R1R2R1+R2R_T=\frac{R_1R_2}{R_1+R_2}

Example:

Two 100,Ω100\\,\Omega resistors are connected in parallel.

RT=100×100100+100R_T=\frac{100\times100}{100+100} RT=50,ΩR_T=50\\,\Omega

The equivalent resistance is 50,Ω50\\,\Omega.

When measuring resistance in an assembled circuit, other connected paths can affect the reading. Disconnecting one or more component leads may be necessary to verify the expected value.

11. Resistance Measurement vs. Continuity Testing

FeatureResistance measurementContinuity testing
Main purposeDetermine resistance numericallyCheck whether a sufficiently low-resistance path exists
UnitOhms (Ω\Omega)Usually a beep or continuity indication
DisplayNumerical resistanceBeep, symbol, or resistance value
Typical useChecking resistor values and component behaviorTesting wires, fuses, switches, and connections
Meter modeΩ\OmegaContinuity symbol, often a sound-wave icon

Continuity mode is useful for quickly identifying low-resistance connections, while resistance mode provides a more specific numerical measurement.

12. Applications of Resistance Measurement

Resistance measurement is widely used in electronics and electrical troubleshooting.

  1. Testing resistors: Confirming component values before circuit assembly.
  2. Checking wires: Identifying broken conductors or unwanted high resistance.
  3. Testing fuses: Checking whether a fuse's internal element is intact.
  4. PCB troubleshooting: Investigating unexpected shorts between circuit points.
  5. Sensor testing: Observing how an LDR or thermistor responds to environmental changes.
  6. Motor testing: Checking winding resistance as one part of diagnosing a motor.
  7. Solder joint inspection: Finding possible open connections or high-resistance joints.
  8. Arduino and ESP32 projects: Checking passive components and wiring before applying power.
  9. Battery and cable maintenance: Investigating suspect connections, although specialized methods may be needed for accurate low-resistance measurements.

13. Common Errors During Resistance Measurement

ErrorResult
Measuring a powered circuitIncorrect readings or possible meter damage
Leaving a resistor connected to parallel pathsReading lower than the component's actual resistance
Using the wrong meter terminalIncorrect operation or potential damage
Poor probe contactUnstable or inaccurate reading
Using an unsuitable rangeOver-range display or poor resolution
Touching exposed probe tips or component leadsBody resistance can affect some high-resistance measurements
Measuring a hot componentResistance may differ from its value at room temperature

14. Safety Precautions

  • Turn off and disconnect the circuit's power before measuring resistance.
  • Safely discharge capacitors before testing.
  • Never measure resistance directly on live mains wiring or an energized circuit.
  • Use the correct multimeter terminals and resistance mode.
  • Isolate the component when connected circuit paths may affect the reading.
  • Do not rely on resistance measurement alone to prove that a semiconductor, motor, or complex electronic component is fully functional.
  • Follow the multimeter manufacturer's instructions and input limits.

15. Summary

Resistance measurement determines how strongly a material or component opposes electric current. It is usually performed using a digital multimeter in resistance mode, with readings expressed in ohms.

This technique is useful for checking resistors, wires, fuses, sensors, solder joints, and electronic circuit connections. Understanding resistance units, resistor tolerance, and series and parallel combinations helps diagnose faults and build reliable electronic projects.

Keep learning. Keep building. Keep growing.

© 2026 Ugenz Academy