Ugenz Academy/IoT Tutorial

Current Divider

7 min read1,342 words

Reading progress

Keep learning

Current Divider

1. What Is a Current Divider?

A current divider is an electrical circuit in which the total current divides between two or more parallel branches.

The amount of current flowing through each branch depends on its resistance. A branch with lower resistance carries more current, while a branch with higher resistance carries less current.

Current dividers are commonly used in parallel resistor circuits, electronic circuit analysis, sensor networks, and current-measurement circuits.

Voltage and Current Division Circuits | CircuitBread

circuitbread.com

For example, suppose a total current of 6 A enters two parallel branches:

  • Branch 1 has a resistance of 2,Ω2\\,\Omega.
  • Branch 2 has a resistance of 4,Ω4\\,\Omega.

More current flows through the 2,Ω2\\,\Omega resistor because it offers less resistance.

The current divider rule helps us calculate exactly how much current flows through each branch.

2. Current Divider Circuit Diagram

Consider a current source connected to two parallel resistors, R1R_1 and R2R_2.

The total current enters the parallel network and splits into branch currents.

In this circuit:

  • ITI_T = total current entering the parallel network.
  • I1I_1 = current flowing through R1R_1.
  • I2I_2 = current flowing through R2R_2.
  • R1R_1 and R2R_2 are connected across the same two nodes.

According to Kirchhoff’s Current Law (KCL):

IT=I1+I2\boxed{I_T=I_1+I_2}

The total current is equal to the sum of all branch currents.

3. Current Divider Formula

For two resistors connected in parallel, the current divider formulas are:

I1=ITR2R1+R2\boxed{I_1=I_T\frac{R_2}{R_1+R_2}} I2=ITR1R1+R2\boxed{I_2=I_T\frac{R_1}{R_1+R_2}}

Notice an important detail: the current through one resistor uses the other resistor in the numerator.

This happens because current divides inversely with resistance.

SymbolMeaningUnit
ITI_TTotal input currentAmpere (A)
I1I_1Current through R1R_1Ampere (A)
I2I_2Current through R2R_2Ampere (A)
R1R_1First branch resistanceOhm (Ω\Omega)
R2R_2Second branch resistanceOhm (Ω\Omega)

General current divider formula

For nn parallel branches, the current through branch kk is:

Ik=IT1/Rk∑_j=1n(1/Rj)\boxed{I_k=I_T\frac{1/R_k}{\sum\_{j=1}^{n}(1/R_j)}}

This formula uses the conductance of each branch, where conductance is the reciprocal of resistance.

G=1RG=\frac{1}{R}

Therefore, current divides in proportion to branch conductance.

4. How Does the Current Divider Formula Work?

Consider two parallel resistors connected to a current source.

Because parallel branches share the same voltage, Ohm’s law gives:

I1=VR1I_1=\frac{V}{R_1} I2=VR2I_2=\frac{V}{R_2}

According to KCL:

IT=I1+I2I_T=I_1+I_2

Substitute the current expressions:

IT=VR1+VR2I_T=\frac{V}{R_1}+\frac{V}{R_2}

Factor out VV:

IT=V(1R1+1R2)I_T=V\left(\frac{1}{R_1}+\frac{1}{R_2}\right)

Solving for the common voltage:

V=ITR1R2R1+R2V=I_T\frac{R_1R_2}{R_1+R_2}

Now substitute VV into I1=V/R1I_1=V/R_1:

I1=ITR1R2R1(R1+R2)I_1=\frac{I_TR_1R_2}{R_1(R_1+R_2)}

Cancel R1R_1:

I1=ITR2R1+R2\boxed{I_1=I_T\frac{R_2}{R_1+R_2}}

Similarly:

I2=ITR1R1+R2\boxed{I_2=I_T\frac{R_1}{R_1+R_2}}

These equations show mathematically why the lower-resistance branch carries more current.

5. Solved Numerical Examples

Example 1: Finding current in two parallel resistors

Suppose a total current of 6 A enters two parallel resistors:

  • R1=2,ΩR_1=2\\,\Omega
  • R2=4,ΩR_2=4\\,\Omega
  • IT=6 AI_T=6\text{ A}

Find the current through each resistor.

Step 1: Calculate I1I_1

I1=ITR2R1+R2I_1=I_T\frac{R_2}{R_1+R_2}

Substitute:

I1=642+4I_1=6\frac{4}{2+4} I1=6×46I_1=6\times\frac{4}{6} I1=4 A\boxed{I_1=4\text{ A}}

Step 2: Calculate I2I_2

I2=ITR1R1+R2I_2=I_T\frac{R_1}{R_1+R_2} I2=622+4I_2=6\frac{2}{2+4} I2=6×26I_2=6\times\frac{2}{6} I2=2 A\boxed{I_2=2\text{ A}}

Step 3: Verify using KCL

IT=I1+I2I_T=I_1+I_2 6=4+26=4+2

The result is correct.

BranchResistanceCurrent
R1R_12,Ω2\\,\Omega4 A
R2R_24,Ω4\\,\Omega2 A
Total—6 A

The 2,Ω2\\,\Omega resistor carries twice as much current as the 4,Ω4\\,\Omega resistor.

Example 2: Current divider with kilo-ohm resistors

Suppose a total current of 12 mA flows into two parallel resistors:

  • R1=3,kΩR_1=3\\,k\Omega
  • R2=6,kΩR_2=6\\,k\Omega

Find both branch currents.

For the first branch:

I1=1263+6I_1=12\frac{6}{3+6} I1=8 mA\boxed{I_1=8\text{ mA}}

For the second branch:

I2=1233+6I_2=12\frac{3}{3+6} I2=4 mA\boxed{I_2=4\text{ mA}}

Check:

12 mA=8 mA+4 mA12\text{ mA}=8\text{ mA}+4\text{ mA}

The current through the 3,kΩ3\\,k\Omega resistor is twice the current through the 6,kΩ6\\,k\Omega resistor.

Example 3: Finding an unknown resistance

A total current of 10 A splits between two parallel resistors. The current through R1=4,ΩR_1=4\\,\Omega is 6 A. Find R2R_2.

First, use KCL to find the second branch current:

I2=IT−I1I_2=I_T-I_1 I2=10−6I_2=10-6 I2=4 AI_2=4\text{ A}

Using the current divider rule:

I1=ITR2R1+R2I_1=I_T\frac{R_2}{R_1+R_2}

Substitute:

6=10R24+R26=10\frac{R_2}{4+R_2}

Multiply both sides:

6(4+R2)=10R26(4+R_2)=10R_2 24+6R2=10R224+6R_2=10R_2 24=4R224=4R_2 R2=6,Ω\boxed{R_2=6\\,\Omega}

The unknown resistor is 6,Ω6\\,\Omega.

6. Interactive Current Divider Calculator

Change the total current and resistor values to see how the current divides between two parallel branches.

Total current (Iₜ)

6 A

1 A

10 A

20 A

Resistance R₁

2 Ω

1 Ω

10 Ω

20 Ω

Resistance R₂

4 Ω

1 Ω

10 Ω

20 Ω

Current through R₁

4.000 A

Current through R₂

2.000 A

Voltage across branches

8.000 V

Total branch current

6.000 A

Assumes an ideal current source and two parallel resistors. The source must be capable of providing the calculated voltage and current.

Reset values

7. Current Divider in Circuits With Multiple Branches

A current divider can have more than two parallel branches.

For three parallel resistors, the total current is:

IT=I1+I2+I3I_T=I_1+I_2+I_3

The current through each branch depends on its conductance.

For example, consider:

  • Total current = 12 A
  • R1=2,ΩR_1=2\\,\Omega
  • R2=3,ΩR_2=3\\,\Omega
  • R3=6,ΩR_3=6\\,\Omega

First, calculate the total conductance:

GT=12+13+16G_T=\frac12+\frac13+\frac16 GT=1 SG_T=1\text{ S}

The branch currents are:

I1=121/21=6 AI_1=12\frac{1/2}{1}=6\text{ A} I2=121/31=4 AI_2=12\frac{1/3}{1}=4\text{ A} I3=121/61=2 AI_3=12\frac{1/6}{1}=2\text{ A}

Check:

12=6+4+212=6+4+2

Therefore, the three branches carry 6 A, 4 A, and 2 A respectively.

8. Current Divider vs. Voltage Divider

Although the names are similar, current dividers and voltage dividers work differently.

FeatureCurrent dividerVoltage divider
Main purposeDivides currentDivides voltage
Typical arrangementParallel resistorsSeries resistors
Main principleCurrent divides inversely with resistanceVoltage divides in proportion to resistance
Lower resistanceCarries more currentHas a smaller voltage drop
Common formulaI1=ITR2R1+R2I_1=I_T\frac{R_2}{R_1+R_2}V1=V_inR1R1+R2V_1=V\_{in}\frac{R_1}{R_1+R_2}

For a current divider, the numerator uses the other branch's resistance. For a voltage divider, the voltage across a resistor uses that resistor's own resistance in the numerator.

9. Applications of Current Dividers

Building Simple Resistor Circuits - Electrical Engineering Textbooks | CircuitBread

A. Parallel resistor circuits

Calculate how much current flows through each resistor when several resistors are connected across the same two nodes.

Shunt vs Hall current sensing for EV batteries | Melexis

B. Current sensing

Analyze current flow in circuits that use shunt resistors and measurement electronics. Actual sensor design must also consider resistor power and measurement accuracy.

bjt - Common Emitter Amplifier DC analysis - Electrical Engineering Stack Exchange

C. Electronic circuit analysis

Work out branch currents in transistor circuits, bias networks, and other networks with parallel paths.

Electrical Loads Connected In Parallel at Sandra Eyre blog

D. Parallel loads

Estimate current distribution among parallel loads when their resistances or impedances are known and the circuit conditions permit this analysis.

10. Important Points to Remember

  • A current divider splits total current among parallel branches.
  • Lower resistance means higher branch current.
  • Higher resistance means lower branch current.
  • For two parallel resistors:
I1=ITR2R1+R2I_1=I_T\frac{R_2}{R_1+R_2} I2=ITR1R1+R2I_2=I_T\frac{R_1}{R_1+R_2}
  • The sum of the branch currents equals the total current, according to KCL.
  • Current divider formulas apply to idealized parallel branches; additional components connected to the same nodes must be included in the analysis.
  • Always check the power ratings of resistors and the current and voltage limits of the circuit.

In short: A current divider helps you calculate how an incoming current splits between parallel branches. The branch with the lowest resistance carries the largest share of the current.

Keep learning. Keep building. Keep growing.

© 2026 Ugenz Academy