Ugenz Academy/IoT Tutorial

Capacitors

9 min read1,798 words

Reading progress

Keep learning

Capacitors

1. Introduction

A capacitor is a passive electronic component that stores electrical energy in an electric field. It can charge when connected to a voltage source and discharge when connected to a suitable circuit.

Capacitors are widely used in electronic circuits for filtering, smoothing voltage, coupling signals, timing, noise reduction, and temporary energy storage.

A capacitor consists of two conductive plates separated by an insulating material called a dielectric. The dielectric prevents direct conduction between the plates while allowing an electric field to form between them.

The ability of a capacitor to store electric charge is called capacitance, which is measured in farads (F).

Common capacitor applications include:

  • Smoothing voltage in power supplies.
  • Reducing electrical noise in circuits.
  • Helping stabilize the supply voltage of microcontrollers.
  • Coupling AC signals between amplifier stages.
  • Creating timing and delay circuits.
  • Storing energy for short periods.

2. Construction of a Capacitor

A capacitor has three main parts.

1. Conductive plates: Two conductive surfaces that hold opposite electrical charges when the capacitor is charged.

2. Dielectric material: The insulating material between the plates. It may be ceramic, plastic film, paper, mica, oxide, or another suitable material.

3. Terminals: The connections used to connect the capacitor to an electronic circuit.

When a voltage source is connected, electrons accumulate on one plate and are removed from the other. This creates an electric field between the plates.

The capacitor stores energy in this electric field. In an ideal capacitor, the dielectric prevents direct current from flowing through the component itself.

3. What Is Capacitance?

Capacitance describes how much electric charge a capacitor stores for a given voltage.

It is represented by the letter CC.

The basic formula is:

C=QVC=\frac{Q}{V}

Where:

  • CC = capacitance in farads (F)
  • QQ = magnitude of stored charge in coulombs (C)
  • VV = voltage across the capacitor in volts (V)

The formula can also be written as:

Q=CVQ=CV

For example, suppose a capacitor has a capacitance of 100,μF100\\,\mu F and is charged to 5 V.

Convert the capacitance into farads:

100,μF=100×10−6F100\\,\mu F=100\times10^{-6}F

Then calculate the charge:

Q=CVQ=CV Q=100×10−6×5Q=100\times10^{-6}\times5 Q=500,μC\boxed{Q=500\\,\mu C}

Therefore, the capacitor stores 500 microcoulombs of charge at 5 V.

4. Units of Capacitance

The standard unit of capacitance is the farad (F).

One farad is a large capacitance for many ordinary electronic circuits, so smaller units are commonly used.

UnitSymbolEquivalent
FaradF1 F
MillifaradmF10−310^{-3} F
MicrofaradμF10−610^{-6} F
NanofaradnF10−910^{-9} F
PicofaradpF10−1210^{-12} F

Examples of common capacitance values include:

  • 100 pF for small signal and high-frequency circuits.
  • 100 nF for supply bypassing and noise reduction.
  • 10 μF for power-supply filtering.
  • 1000 μF for bulk energy storage and smoothing.

The appropriate capacitance depends on the circuit's operating frequency, required filtering, voltage, and load current.

5. How Does a Capacitor Work?

A capacitor's behavior can be understood in three stages.

A. Charging

When a capacitor is connected to a DC voltage source through a circuit, charge accumulates on its plates.

Initially, an uncharged capacitor can allow a charging current to flow. As its voltage rises, the charging current generally decreases in a simple resistor-capacitor circuit.

For an ideal capacitor, charging is described by:

i=CdVdti=C\frac{dV}{dt}

Where:

  • ii = current through the capacitor
  • CC = capacitance
  • dVdt\frac{dV}{dt} = rate of change of voltage

This equation means that a faster change in voltage requires a greater current for the same capacitance.

B. Fully Charged State

When a capacitor in a simple DC circuit reaches a steady voltage, the ideal capacitor stops drawing continuous charging current.

Therefore, an ideal capacitor behaves like an open circuit for steady-state DC.

Real capacitors have small leakage currents, so they are not perfect insulators.

C. Discharging

When a charged capacitor is connected across a suitable load, it releases its stored energy and its voltage decreases.

The discharge rate depends on the capacitance and the resistance of the discharge path.

A larger capacitance generally takes longer to discharge through the same resistance.

Important: A capacitor can remain charged after a circuit is disconnected from its power supply. High-voltage and large-capacitance capacitors can be dangerous and must be discharged using appropriate procedures.

6. Types of Capacitors

Capacitors are available in several types. Their construction affects capacitance, voltage rating, polarity, accuracy, stability, and typical applications.

20 Pcs 1000uF 50V 13x25mm Aluminum Electrolytic Capacitors Black | Fruugo UK

1. Electrolytic Capacitor

Electrolytic capacitors provide relatively high capacitance in a compact size. Many common aluminum electrolytic capacitors are polarized, meaning their positive and negative terminals must be connected correctly.

Applications: Power-supply smoothing, bulk filtering, and low-frequency coupling where suitable.

Selection Guide | Murata Manufacturing Co., Ltd.

2. Ceramic Capacitor

Ceramic capacitors use ceramic dielectric material. Many are non-polarized and are available in very small packages.

Their capacitance stability depends on the ceramic dielectric class.

Applications: Noise suppression, high-frequency filtering, decoupling, and signal circuits.

Buy 0.1uf 310V Film Polyester Box Capacitor (Pack of 100) at HNHcart.com

3. Film Capacitor

Film capacitors use a thin plastic film as the dielectric. Many have good stability and are non-polarized.

Applications: Audio circuits, signal coupling, timing circuits, and suitable AC applications.

10nF 500V Radial Silver Mica Capacitor CM07FD | Radio741

4. Mica Capacitor

Mica capacitors use mica as the dielectric and are known for good stability and low losses in suitable designs.

Applications: Precision and radio-frequency circuits where their characteristics are appropriate.

Unlocking the Power of Variable Capacitors: A Comprehensive Guide - | AnyPCBA

5. Variable Capacitor

A variable capacitor allows its capacitance to be adjusted mechanically. Some designs change the overlap between conductive plates or the dielectric arrangement.

Applications: Radio tuning, resonant circuits, and specialized RF equipment.

7. Polarized and Non-Polarized Capacitors

Capacitors are also classified according to whether their terminals have a required polarity.

Polarized Capacitors

Polarized capacitors have positive and negative terminals. Common aluminum electrolytic capacitors are an example.

Their polarity must be respected when connecting them to a DC circuit. Reverse polarity can cause excessive leakage, overheating, damage, or even rupture.

Non-Polarized Capacitors

Non-polarized capacitors can generally be connected in either direction within their ratings.

Common examples include many ceramic and film capacitors.

They are useful in AC signal circuits and other applications where the voltage polarity may alternate.

The component's datasheet should always be checked to confirm its polarity and operating limits.

8. Capacitors in Series

When capacitors are connected in series, the positive terminal of one may connect to the negative terminal of another in appropriate polarized DC arrangements, or non-polarized capacitors may be used according to the circuit design.

The equivalent capacitance is calculated using:

1CT=1C1+1C2+1C3\frac{1}{C_T}= \frac{1}{C_1}+\frac{1}{C_2}+\frac{1}{C_3}

For two capacitors:

CT=C1C2C1+C2C_T=\frac{C_1C_2}{C_1+C_2}

Example: Two capacitors of 10 μF and 20 μF are connected in series.

CT=10×2010+20C_T=\frac{10\times20}{10+20} CT=20030C_T=\frac{200}{30} CT≈6.67,μF\boxed{C_T\approx6.67\\,\mu F}

The equivalent capacitance is lower than either individual capacitance.

In practical circuits, series-connected capacitors may need voltage-balancing components because their leakage currents and capacitances can differ.

9. Capacitors in Parallel

When capacitors are connected in parallel, each capacitor has the same voltage across it.

Their capacitances add together:

CT=C1+C2+C3+⋯+CnC_T=C_1+C_2+C_3+\cdots+C_n

Example: Three capacitors of 10 μF, 22 μF, and 100 μF are connected in parallel.

CT=10+22+100C_T=10+22+100 CT=132,μF\boxed{C_T=132\\,\mu F}

Connecting capacitors in parallel increases the total capacitance and the amount of charge stored at a given voltage.

The combined voltage rating must still be respected; connecting capacitors in parallel does not automatically increase their voltage rating.

10. Energy Stored in a Capacitor

A capacitor stores energy in its electric field.

The stored energy is calculated using:

E=12CV2E=\frac{1}{2}CV^2

Where:

  • EE = energy in joules (J)
  • CC = capacitance in farads (F)
  • VV = voltage across the capacitor in volts (V)

Example: A 1000 μF capacitor is charged to 12 V.

First, convert the capacitance:

1000,μF=0.001,F1000\\,\mu F=0.001\\,F

Then calculate the energy:

E=12×0.001×122E=\frac{1}{2}\times0.001\times12^2 E=0.072,JE=0.072\\,J

Therefore:

E=0.072,J\boxed{E=0.072\\,J}

The stored energy increases with capacitance and with the square of the voltage.

11. Capacitors in DC and AC Circuits

A capacitor behaves differently depending on whether the applied voltage is steady or changing.

In a steady DC circuit: After charging is complete, an ideal capacitor carries no continuous current.

In an AC circuit: The voltage continuously changes, so the capacitor repeatedly charges and discharges. This allows alternating current to flow through the external circuit.

The opposition a capacitor presents to sinusoidal AC is called capacitive reactance.

It is calculated using:

XC=12πfCX_C=\frac{1}{2\pi fC}

Where:

  • XCX_C = capacitive reactance in ohms
  • ff = frequency in hertz
  • CC = capacitance in farads

A higher frequency or larger capacitance results in lower capacitive reactance.

This is why capacitors can be used to separate or filter signals at different frequencies.

12. RC Circuits and Time Constant

An RC circuit contains a resistor (R) and a capacitor (C).

RC circuits are used for timing, filtering, delays, signal processing, and controlling how quickly a capacitor charges or discharges.

The time constant is:

τ=RC\tau=RC

Where:

  • τ\tau = time constant in seconds
  • RR = resistance in ohms
  • CC = capacitance in farads

For example, if a 10 kΩ resistor is connected in series with a 100 μF capacitor:

τ=10000×100×10−6\tau=10000\times100\times10^{-6} τ=1,second\boxed{\tau=1\\,\text{second}}

For a simple RC charging circuit supplied by a step voltage, the capacitor reaches approximately 63.2% of its final voltage after one time constant.

After about five time constants, it reaches more than 99% of its final voltage.

This behavior is useful when designing delays, smoothing signals, and simple filters.

13. Applications of Capacitors

Capacitors are essential components in many electronic systems.

  • Power supplies: Smooth rectified voltage and reduce ripple.
  • Microcontrollers: Decouple supply pins to reduce voltage fluctuations and electrical noise.
  • Audio circuits: Couple AC signals between stages while blocking steady DC, when designed appropriately.
  • Timing circuits: Work with resistors to establish charging and discharging intervals.
  • Filters: Attenuate or pass certain frequency ranges.
  • Motors: Suitable capacitors help start or run certain AC motors.
  • Energy storage: Supply short bursts of energy in applications such as camera flashes and pulse circuits.
  • Oscillators: Help determine the frequency of oscillation in suitable circuits.

The correct capacitor depends on the required capacitance, voltage rating, dielectric type, polarity, frequency characteristics, tolerance, temperature range, and equivalent series resistance (ESR).

Keep learning. Keep building. Keep growing.

© 2026 Ugenz Academy