Ugenz Academy/IoT Tutorial

Rl Circuits

10 min read1,831 words

Reading progress

Keep learning

RL Circuits (Resistor-Inductor Circuits)

1. What Is an RL Circuit?

An RL circuit is an electrical circuit that contains a resistor (R) and an inductor (L). It is used to study how current changes over time when voltage is applied or removed.

A resistor limits current and converts electrical energy into heat, while an inductor stores energy in a magnetic field when current flows through it.

A 10.0 milliHenry inductor and a 4.5-ohm resistor are wired in series to a 9-volt battery. A switch in the circuit is closed at time 0, at which time the current is zero. After a long time, the voltage across the resistor and the voltage across the induct | Homework.Study.com

10.12: Growth of Current in a Circuit Containing Inductance - Physics LibreTexts

Inductor and Resistor: A Comparative Guide

6

RL circuits are commonly used in:

  • Electromagnets and relay circuits
  • Electric motors and solenoids
  • Power supplies and switching converters
  • Signal filters
  • Motor-control circuits
  • Automotive electronics
  • Transient and switching circuits

The behavior of an RL circuit depends on the resistance, inductance, applied voltage, and elapsed time.

2. Main Components of an RL Circuit

Royal Ohm CFR01SJ0330A10 33R 5% 1W Axial Carbon Film Resistor | Rapid Electronics

A. Resistor (R)

A resistor opposes current flow and converts some electrical energy into heat. Its resistance is measured in ohms (Ω\Omega).

A higher resistance generally causes the current in a series RL circuit to reach its final value more quickly.

Inductor symbol Explained: Diagrams, Polarity & Real-World Use Cases | Ersa Electronics

B. Inductor (L)

An inductor is typically a coil of wire that stores energy in a magnetic field. Its inductance is measured in henries (H).

An inductor opposes changes in current. It does not oppose steady current in an ideal DC circuit after the transient has ended.

Important inductor formulas

The voltage across an ideal inductor is:

VL=Ldidt\boxed{V_L=L\frac{di}{dt}}

Where:

  • VLV_L = inductor voltage in volts (V)
  • LL = inductance in henries (H)
  • di/dtdi/dt = rate of change of current in amperes per second (A/s)

The energy stored in an ideal inductor is:

E=12LI2\boxed{E=\frac12 LI^2}

Where EE is measured in joules (J), and II is the current through the inductor.

3. Basic RL Circuit Diagram

A basic series RL circuit contains a voltage source, a resistor, and an inductor connected in one loop.

The resistor and inductor share the same current because they are connected in series.

When a DC voltage source is connected, the current does not immediately reach its final value. The inductor generates a voltage that opposes the change in current.

As time passes, the current increases. Once the current becomes steady, the ideal inductor's voltage becomes zero.

4. Working of an RL Circuit

An RL circuit has two important operating conditions: current growth when the source is connected and current decay when the source is removed.

A. Current growth (switch ON)

When the circuit is connected to a DC source:

  1. Initially, the inductor opposes the rapid increase in current.
  2. The current starts increasing from zero.
  3. The inductor's voltage decreases as the rate of current change decreases.
  4. Eventually, the current approaches a steady value determined by the supply voltage and resistance.

Transients in an Inductor

hyperphysics.phy-astr.gsu.edu

Current growth formula

For a series RL circuit initially carrying zero current:

i(t)=VSR(1−e−tR/L)\boxed{i(t)=\frac{V_S}{R}\left(1-e^{-tR/L}\right)}

Where:

  • i(t)i(t) = current at time tt
  • VSV_S = DC supply voltage
  • RR = total series resistance
  • LL = inductance
  • tt = elapsed time
  • ee = mathematical constant, approximately 2.718

The final steady-state current is:

I_∞=VSR\boxed{I\_{\infty}=\frac{V_S}{R}}

This follows from Ohm's law because an ideal inductor behaves like a short circuit under steady DC conditions.

B. Current decay (switch OFF)

When the source is removed, the inductor attempts to maintain the current that was already flowing.

If a closed discharge path remains, the magnetic field releases its stored energy and the current gradually decreases.

RL Circuit Behavior: Natural Response and Singularity Functions

engineeringdevotion.com

Current decay formula

If the initial current is I0I_0, then:

i(t)=I0e−tR/L\boxed{i(t)=I_0e^{-tR/L}}

The current approaches zero as time increases, assuming the circuit provides a resistive discharge path.

Important: An inductor can generate a large voltage when its current is interrupted abruptly. A practical circuit may require a flyback diode or another suitable clamp to protect switches and electronic components.

5. Time Constant of an RL Circuit

The time constant of a series RL circuit tells us how quickly its current rises or falls.

It is represented by τ\tau (tau).

τ=LR\boxed{\tau=\frac{L}{R}}

Where:

  • τ\tau = time constant in seconds
  • LL = inductance in henries
  • RR = total series resistance in ohms

A larger inductance increases the time constant, making the current change more slowly. A larger resistance decreases the time constant, making the current approach its final value more quickly.

Current growth and decay percentages

Elapsed timeGrowth: percentage of final currentDecay: percentage of initial current remaining
1τ1\tau63.2%36.8%
2τ2\tau86.5%13.5%
3τ3\tau95.0%5.0%
4τ4\tau98.2%1.8%
5τ5\tau99.3%0.7%

After approximately five time constants, the current is usually considered practically settled.

6. Solved Numerical Examples

Example 1: Calculate the time constant

A 2,H2\\,H inductor is connected in series with a 10,Ω10\\,\Omega resistor. Find the time constant.

Given:

L=2,H,R=10,ΩL=2\\,H,\qquad R=10\\,\Omega

Using:

τ=LR\tau=\frac{L}{R} τ=210\tau=\frac{2}{10} τ=0.2 s\boxed{\tau=0.2\text{ s}}

The time constant is 0.2 seconds.

Example 2: Calculate the final current

A 12 V DC source is connected to a series RL circuit with a 6,Ω6\\,\Omega resistor and an ideal inductor. Find the steady-state current.

Using Ohm's law:

I_∞=VSRI\_{\infty}=\frac{V_S}{R} I_∞=126I\_{\infty}=\frac{12}{6} I_∞=2 A\boxed{I\_{\infty}=2\text{ A}}

The final current is 2 A.

Example 3: Calculate current during growth

A 12 V source supplies a series RL circuit with:

  • R=6,ΩR=6\\,\Omega
  • L=3,HL=3\\,H

Find the current after 0.5 seconds, assuming the initial current is zero.

First, calculate the time constant:

τ=LR=36=0.5 s\tau=\frac{L}{R}=\frac{3}{6}=0.5\text{ s}

Calculate the final current:

I_∞=126=2 AI\_{\infty}=\frac{12}{6}=2\text{ A}

Use the current growth formula:

i(t)=I_∞(1−e−t/τ)i(t)=I\_{\infty}(1-e^{-t/\tau})

At t=0.5 st=0.5\text{ s}:

i(0.5)=2(1−e−1)i(0.5)=2(1-e^{-1}) i(0.5)=2(1−0.368)i(0.5)=2(1-0.368) i(0.5)≈1.26 A\boxed{i(0.5)\approx1.26\text{ A}}

After 0.5 seconds, the current is approximately 1.26 A.

Example 4: Calculate current during decay

An inductor carries an initial current of 4 A. It discharges through a resistor with a time constant of 2 seconds. Find the current after 4 seconds.

Given:

I0=4 A,τ=2 sI_0=4\text{ A},\qquad \tau=2\text{ s}

Use the decay formula:

i(t)=I0e−t/τi(t)=I_0e^{-t/\tau}

Substitute:

i(4)=4e−4/2i(4)=4e^{-4/2} i(4)=4e−2i(4)=4e^{-2} i(4)≈0.54 A\boxed{i(4)\approx0.54\text{ A}}

After 4 seconds, approximately 0.54 A remains.

7. Interactive RL Time Constant Calculator

Change the resistance, inductance, supply voltage, and elapsed time to calculate current growth or decay.

Resistance

10 Ω

1 Ω

50 Ω

100 Ω

Inductance

2.0 H

0.1 H

5 H

10 H

Supply voltage

12 V

1 V

12 V

24 V

Operating mode

Current growth

Current decay

Elapsed time

0.20 s

0 s

Midpoint

End

Time constant (τ)

0.200 seconds

Calculated current

0.759 A

63.2% of the steady-state current

Assumes a linear inductor, fixed resistance, and zero initial current for growth. For decay, the initial current is assumed to equal the calculated steady-state current, with a closed resistive discharge path.

Reset values

8. RL Circuits as Filters

An RL circuit can act as a frequency-selective filter. The output voltage depends on the frequency of the input signal and where the output is measured.

RL Low-Pass Filter Calculator

A. Low-pass filter

In a series RL network, taking the output across the resistor produces a low-pass response. Low-frequency signals pass more readily, while high-frequency signals are attenuated.

High Pass Filter Calculator

B. High-pass filter

Taking the output across the inductor in the same series RL network produces a high-pass response. The inductor's impedance increases with frequency, so the output across it increases relative to the input.

Cutoff frequency

For a simple series RL filter with an ideal inductor and resistor:

fc=R2πL\boxed{f_c=\frac{R}{2\pi L}}

Where:

  • fcf_c = cutoff frequency in hertz (Hz)
  • RR = resistance in ohms
  • LL = inductance in henries

At the cutoff frequency, the output magnitude is approximately 70.7% of its passband value, or −3 dB-3\text{ dB}.

Numerical example

Suppose:

R=100,Ω,L=0.1,HR=100\\,\Omega,\qquad L=0.1\\,H

Then:

fc=1002π(0.1)f_c=\frac{100}{2\pi(0.1)} fc≈159.2 Hz\boxed{f_c\approx159.2\text{ Hz}}

The circuit's cutoff frequency is approximately 159.2 Hz.

9. Applications of RL Circuits

What Is A Relay And How Does It Work? Wiring Diagrams, DPDT Schematic, And How To Test A Relay Explained

A. Relay and solenoid circuits

Coils create magnetic fields to operate relay contacts, door locks, and electromagnetic actuators. Their inductance affects how current changes when switching.

Electric motor stator winding and stack close-up

B. Electric motors

Motor windings have resistance and inductance. RL behavior influences starting current, switching transients, and electrical response.

Mikrobot | DC 4V-38V 5A step-down converter module - Reducing voltage to 1.25V-36V

C. Power electronics

Inductors store energy and help control current in switching converters. Real converter designs also involve switching behavior, capacitors, and control circuits.

D. Signal filtering

RL filters can pass or attenuate selected frequency ranges in electronic and communication circuits.

10. Difference Between RC and RL Circuits

FeatureRC circuitRL circuit
ComponentsResistor and capacitorResistor and inductor
Energy storageElectric fieldMagnetic field
Main changing quantityCapacitor voltageInductor current
Time constantτ=RC\tau=RCτ=L/R\tau=L/R
DC charging or growthCapacitor voltage rises graduallyInductor current rises gradually
DC decayCapacitor voltage falls through a discharge pathInductor current falls through a discharge path
Filter cutoff frequencyfc=1/(2πRC)f_c=1/(2\pi RC)fc=R/(2πL)f_c=R/(2\pi L)

11. Important Points to Remember

  • An RL circuit contains a resistor and an inductor.
  • An inductor opposes changes in current.
  • The inductor stores energy in a magnetic field.
  • The time constant of a series RL circuit is τ=L/R\tau=L/R.
  • After one time constant, current growth reaches about 63.2% of its final value.
  • After one time constant, current decay leaves about 36.8% of its initial value.
  • The steady-state current for a DC source and ideal series inductor is I=VS/RI=V_S/R.
  • RL circuits are used in motors, relays, filters, and switching power supplies.

In short: An RL circuit uses resistance and inductance to control how current changes over time. Its time constant determines how quickly current rises or falls, making RL circuits useful in electromagnetic devices, power electronics, and signal filtering.

Keep learning. Keep building. Keep growing.

© 2026 Ugenz Academy