IotIntermediate

TCS3200 RGB Frequency Measurement

Measure red, green, and blue color frequencies using the TCS3200 sensor and Arduino.

Technologies Used

Arduino UnoTCS3200 Color SensorSerial Monitor

Arduino TCS3200 Color Sensor – RGB Frequency Measurement

1. Introduction

The TCS3200 (TCS230) is an RGB color sensor used to detect the color of objects. It contains photodiodes with red, green, blue, and clear filters.

The sensor converts the intensity of detected light into a frequency signal. Arduino reads this signal and measures the LOW pulse duration using the pulseIn() function.

In this project, Arduino reads the red, green, and blue filter outputs and displays the measured values on the Serial Monitor.

2. Objectives

  • To interface the TCS3200 color sensor with Arduino.
  • To understand RGB color filters.
  • To measure the sensor output pulse duration.
  • To read red, green, and blue sensor values.
  • To display sensor readings on the Serial Monitor.

3. Required Components

  1. Arduino Uno
  2. TCS3200 / TCS230 color sensor
  3. Jumper wires
  4. USB cable
  5. Computer with Arduino IDE

4. About TCS3200 Sensor

The TCS3200 is a color sensor that detects light intensity using different photodiode filters.

It contains four types of photodiodes:

  • Red filter photodiodes
  • Green filter photodiodes
  • Blue filter photodiodes
  • Clear photodiodes

The sensor produces a square-wave output whose frequency depends on the detected light intensity.

5. Pin Configuration

Sensor PinFunction
VCCPower supply
GNDGround
S0Frequency scaling selection
S1Frequency scaling selection
S2Color filter selection
S3Color filter selection
OUTFrequency signal output
OEOutput enable

6. Arduino Connections

TCS3200 PinArduino Uno Pin
S0D4
S1D5
S2D6
S3D7
OUTD8
VCC5V, if supported by the module
GNDGND
OEGND, if required

Note: Check the voltage requirements and OE connection of your particular sensor module.

7. RGB Filter Selection

The S2 and S3 pins select which photodiode filter is active.

Color FilterS2S3
RedLOWLOW
GreenHIGHHIGH
BlueLOWHIGH
ClearHIGHLOW

This program reads only the red, green, and blue filters.

8. Complete Arduino Code

// TCS230 or TCS3200 pins wiring to Arduino #define S0 4 #define S1 5 #define S2 6 #define S3 7 #define sensorOut 8 // Stores frequency read by the photodiodes int redFrequency = 0; int greenFrequency = 0; int blueFrequency = 0; void setup() { // Setting the outputs pinMode(S0, OUTPUT); pinMode(S1, OUTPUT); pinMode(S2, OUTPUT); pinMode(S3, OUTPUT); // Setting the sensorOut as an input pinMode(sensorOut, INPUT); // Setting frequency scaling to 20% digitalWrite(S0, HIGH); digitalWrite(S1, LOW); // Begins serial communication Serial.begin(9600); } void loop() { // Read RED filter digitalWrite(S2, LOW); digitalWrite(S3, LOW); redFrequency = pulseIn(sensorOut, LOW); Serial.print("R = "); Serial.print(redFrequency); delay(100); // Read GREEN filter digitalWrite(S2, HIGH); digitalWrite(S3, HIGH); greenFrequency = pulseIn(sensorOut, LOW); Serial.print(" G = "); Serial.print(greenFrequency); delay(100); // Read BLUE filter digitalWrite(S2, LOW); digitalWrite(S3, HIGH); blueFrequency = pulseIn(sensorOut, LOW); Serial.print(" B = "); Serial.println(blueFrequency); delay(100); }

9. Explanation of the Code

9.1 Define Sensor Pins

#define S0 4 #define S1 5 #define S2 6 #define S3 7 #define sensorOut 8

These statements assign Arduino digital pins to the sensor.

  • S0 and S1 control frequency scaling.
  • S2 and S3 select the color filter.
  • sensorOut receives the sensor's output signal.

9.2 Declare Variables

int redFrequency = 0; int greenFrequency = 0; int blueFrequency = 0;

These variables store the measured LOW pulse durations for the three color filters.

The readings are expressed in microseconds because pulseIn() returns pulse duration in microseconds.

9.3 Setup Function

void setup() { pinMode(S0, OUTPUT); pinMode(S1, OUTPUT); pinMode(S2, OUTPUT); pinMode(S3, OUTPUT); pinMode(sensorOut, INPUT); digitalWrite(S0, HIGH); digitalWrite(S1, LOW); Serial.begin(9600); }

The setup() function executes once when Arduino starts.

  • pinMode(): Configures Arduino pins.
  • OUTPUT: Makes a pin send signals.
  • INPUT: Makes a pin receive signals.
  • digitalWrite(): Sets a digital pin HIGH or LOW.
  • Serial.begin(9600): Starts serial communication at 9600 baud.

9.4 Frequency Scaling

digitalWrite(S0, HIGH); digitalWrite(S1, LOW);

These settings select 20% frequency scaling.

S0S1Frequency Scaling
LOWLOWPower down
LOWHIGH2%
HIGHLOW20%
HIGHHIGH100%

9.5 Read Red Frequency

digitalWrite(S2, LOW); digitalWrite(S3, LOW); redFrequency = pulseIn(sensorOut, LOW);

This selects the red photodiode filter.

The pulseIn() function measures how long the sensor output remains LOW.

9.6 Display Red Reading

Serial.print("R = "); Serial.print(redFrequency);

These statements display the red filter measurement in the Serial Monitor.

9.7 Read Green Frequency

digitalWrite(S2, HIGH); digitalWrite(S3, HIGH); greenFrequency = pulseIn(sensorOut, LOW);

This selects the green photodiode filter and measures its LOW pulse duration.

9.8 Display Green Reading

Serial.print(" G = "); Serial.print(greenFrequency);

This displays the green filter measurement.

9.9 Read Blue Frequency

digitalWrite(S2, LOW); digitalWrite(S3, HIGH); blueFrequency = pulseIn(sensorOut, LOW);

This selects the blue photodiode filter and measures its LOW pulse duration.

9.10 Display Blue Reading

Serial.print(" B = "); Serial.println(blueFrequency);

This displays the blue filter measurement and moves to a new line.

9.11 Delay Function

delay(100);

This pauses the program for approximately 100 milliseconds before continuing.

10. Working Principle

  1. Arduino initializes the sensor pins.
  2. The sensor frequency scaling is set to 20%.
  3. Arduino selects the red filter.
  4. The sensor generates a frequency output.
  5. Arduino measures its LOW pulse duration.
  6. Arduino repeats the same process for the green filter.
  7. Arduino reads the blue filter.
  8. All three measurements are displayed on the Serial Monitor.
  9. The process repeats continuously.

11. Block Diagram

Colored Object | v TCS3200 Sensor | RGB Filter Selection | v Arduino | Pulse Duration Reading | v Serial Monitor | R / G / B Values

12. Flowchart

START | v Initialize Pins | v Set Frequency Scaling | v Select RED Filter | v Read RED Pulse Time | v Select GREEN Filter | v Read GREEN Pulse Time | v Select BLUE Filter | v Read BLUE Pulse Time | v Display RGB Readings | v Repeat Process

13. Expected Output

Open the Serial Monitor and set the baud rate to 9600.

Example:

R = 125 G = 140 B = 110 R = 120 G = 135 B = 105 R = 80 G = 150 B = 125 R = 95 G = 100 B = 160

These values are examples only. Actual readings depend on lighting, object color, sensor distance, and the module.

Important: The program measures pulse duration, not frequency directly. A shorter LOW pulse generally corresponds to a higher output frequency.

14. Important Functions

FunctionPurpose
pinMode()Configures pin direction
digitalWrite()Sets a digital pin HIGH or LOW
pulseIn()Measures pulse duration in microseconds
Serial.begin()Starts serial communication
Serial.print()Prints data without a new line
Serial.println()Prints data with a new line
delay()Pauses the program

15. Difference Between This Program and Color Detection

Basic RGB Reading ProgramRGB Color Detection Program
Reads raw pulse durationsConverts readings into RGB values
Displays red, green, blue measurementsIdentifies the strongest color
Does not require mapping valuesRequires calibration values
Used for sensor testingUsed for basic color identification

16. Troubleshooting

ProblemPossible Solution
No readingsCheck sensor power and wiring
Readings remain zeroCheck OUT pin and OE configuration
Readings fluctuateKeep lighting and object distance stable
Serial Monitor is blankSelect 9600 baud
Wrong readingsCheck S2 and S3 connections

17. Precautions

  • Connect the sensor pins correctly.
  • Check the sensor's voltage requirements.
  • Maintain a consistent distance from the object.
  • Avoid changing the surrounding light during testing.
  • Ensure the OE pin is enabled.
  • Use calibration if accurate color identification is required.

18. Applications

  1. Color detection systems.
  2. Color sorting machines.
  3. Robotics projects.
  4. Industrial automation.
  5. Object identification.
  6. Educational electronics projects.

19. Viva Questions and Answers

Q1. What is TCS3200?

TCS3200 is a color sensor that measures light intensity using different photodiode filters.

Q2. What does RGB stand for?

RGB stands for Red, Green, and Blue.

Q3. How many filter types does TCS3200 have?

It has four filter types: red, green, blue, and clear.

Q4. What is the purpose of S0 and S1?

They select the output frequency scaling.

Q5. What is the purpose of S2 and S3?

They select the photodiode filter.

Q6. What is pulseIn()?

It is an Arduino function that measures the duration of a digital pulse.

Q7. What unit does pulseIn() return?

It returns the pulse duration in microseconds.

Q8. What is frequency scaling?

Frequency scaling changes the output frequency range of the sensor.

Q9. What is the purpose of Serial Monitor?

It displays sensor readings and other messages from Arduino.

Q10. Does this program identify colors automatically?

No. It only reads and displays the red, green, and blue filter pulse durations.

20. Conclusion

In this project, we interfaced the TCS3200 color sensor with Arduino to measure red, green, and blue filter output pulse durations. Arduino selects each color filter and reads the sensor output using the pulseIn() function.

This project helps us understand RGB sensing, photodiode filters, frequency measurement, and Arduino sensor interfacing.


Project Name: Arduino TCS3200 RGB Frequency Measurement

Microcontroller: Arduino Uno

Sensor: TCS3200 / TCS230

Programming Language: C/C++ (Arduino)

Communication: Serial Communication

Output: Red, Green, and Blue pulse-duration readings.