Ugenz Academy/IoT Tutorial

Oscilloscope

12 min read2,282 words

Reading progress

Keep learning

Oscilloscope in Electronics

1. Introduction to an Oscilloscope

An oscilloscope is an electronic measuring instrument used to observe how an electrical signal changes over time. It displays a signal as a graph on a screen, allowing us to study voltage, timing, frequency, noise, and signal shape.

A multimeter usually displays a numerical measurement, while an oscilloscope shows the actual waveform. This makes an oscilloscope especially useful for troubleshooting electronic circuits, microcontrollers, communication systems, and power supplies.

For example, when an ESP32 sends a PWM signal to control a motor, an oscilloscope can show how quickly the signal switches on and off and what its voltage levels look like.

Electronic Product Testing and Quality Assurance

toucan-systems.co.uk

2. Why Is an Oscilloscope Needed?

An oscilloscope helps engineers and technicians understand electrical signals that change over time.

Its main purposes include:

  • Observing electrical waveforms.
  • Measuring signal voltage and timing.
  • Calculating signal frequency and period.
  • Checking PWM signals from Arduino and ESP32.
  • Detecting noise, glitches, and unexpected voltage changes.
  • Testing audio circuits and communication signals.
  • Troubleshooting power supplies and motor-control circuits.

For example, a multimeter may show an average voltage of 2.5,V2.5\\,V for a switching signal, but an oscilloscope can reveal that the signal alternates between 0,V0\\,V and 5,V5\\,V.

3. How Does an Oscilloscope Work?

An oscilloscope measures an input signal and plots its voltage against time.

The horizontal axis represents time, while the vertical axis represents voltage.

Analysis of Common Oscilloscope Terms-EEWORLD

en.eeworld.com.cn

A simplified process is:

  1. A probe connects the oscilloscope to the circuit.
  2. The input circuitry conditions the signal for measurement.
  3. The oscilloscope samples the signal at regular intervals.
  4. The device processes and displays the samples as a waveform.
  5. The user adjusts the time scale, voltage scale, and trigger settings to examine the signal.

Digital oscilloscopes store sampled data in memory, allowing them to display, measure, and analyze signals.

4. Main Parts of an Oscilloscope

UNI-T Speicher-Oszilloskop UTD2102CEX+, 2 Kanal, 100 MHz

pollin.de

PartFunction
DisplayShows the waveform and measurement information
Channel inputsConnect probes to the signals being measured
ProbeCarries the electrical signal from the circuit
Vertical controlsAdjust voltage per division
Horizontal controlsAdjust time per division
Trigger controlsStabilize the waveform display
Measure controlsShow values such as frequency, amplitude, and period
Time baseDetermines the horizontal time scale
Run/Stop controlStarts or pauses acquisition

The exact controls depend on the oscilloscope model.

5. Understanding the Oscilloscope Screen

Most oscilloscopes display a grid called a graticule. Each square is called a division.

Two important settings determine how to read this grid:

  • Volts/division (V/div): The voltage represented by one vertical division.
  • Time/division (s/div): The time represented by one horizontal division.

Example: Measuring Voltage

Suppose a waveform extends 4 vertical divisions from its lowest point to its highest point, and the vertical scale is 2,V/div2\\,V/\text{div}.

V_pp=4×2V\_{pp}=4\times2 V_pp=8,VV\_{pp}=8\\,V

The peak-to-peak voltage is 8,V8\\,V.

Example: Measuring Time

Suppose one complete waveform cycle occupies 5 horizontal divisions, and the time scale is 1,ms/div1\\,ms/\text{div}.

T=5×1,ms=5,msT=5\times1\\,ms=5\\,ms

The signal period is 5,ms5\\,ms.

6. Types of Oscilloscopes

Keysight DSOX1202A - Oscilloscope 2x70MHz | Polytech Instrumentation

1. Digital Storage Oscilloscope (DSO)

Samples and stores waveforms digitally.

  • Can capture and replay signals.
  • Often provides automatic measurements.
  • Common in electronics laboratories and repair workshops.

通过示波器主板讲解示波器原理-qq2850503026-电子技术应用-AET-中国科技核心期刊-最丰富的电子设计资源平台

2. Analog Oscilloscope

Uses a cathode-ray tube (CRT) to display signals.

  • Shows changing signals continuously.
  • Useful for learning traditional measurement concepts.
  • Less common than digital models today.

OWON HDS2102 2 in 1 Digital Oscilloscope AU Plug

3. Handheld Oscilloscope

A portable instrument designed for measurements outside a traditional laboratory.

  • Useful for field troubleshooting.
  • May combine multimeter and oscilloscope functions.
  • Capabilities vary widely between models.

Digilent Analog Discovery Support from MATLAB - Hardware Support - MATLAB & Simulink

4. USB Oscilloscope

Connects to a computer and uses software to display and analyze signals.

  • Often compact and affordable.
  • Useful for learning and small projects.
  • Depends on computer software and the device's specifications.

7. Common Types of Waveforms

Electrical signals can have different shapes. Their appearance can help identify how a circuit operates.

1. Sine Wave

What is a Pure Sine Wave Inverter?

bluettipower.com

A smooth, repeating waveform commonly found in AC power, audio signals, and oscillators.

2. Square Wave

UPO1000CS - Digital Oscilloscopes - Digital Oscilloscopes - UNI-T Voltage Meter, Multimeter, Oscilloscope | UNI-T-UNI-T Voltage Meter, Multimeter, Oscilloscope | UNI-T

instruments.uni-trend.com

Alternates between high and low levels. It is common in digital electronics and clock signals.

3. Triangle Wave

Rises and falls approximately linearly. It is used in waveform generators and some control circuits.

4. Pulse or PWM Wave

Sterownik PWM 4V-30V 1Hz-160kHz dwukanałowy z LED - Sklep, Opinie, Cena w Allegro

allegro.pl

Contains pulses separated by lower-voltage intervals. PWM is widely used for motor speed control, LED dimming, and power conversion.

8. Important Oscilloscope Measurements

An oscilloscope can measure or help calculate several important signal properties.

QuantitySymbolMeaning
Peak voltageVpV_pVoltage measured from the reference level to a waveform peak
Peak-to-peak voltageV_ppV\_{pp}Difference between maximum and minimum voltage
PeriodTTTime for one complete cycle
FrequencyffNumber of cycles per second
Duty cycleDDPercentage of a period spent in the active state
Rise timetrt_rTime taken for a signal to rise between specified levels
Fall timetft_fTime taken for a signal to fall between specified levels
Phase differenceϕ\phiRelative timing difference between periodic signals

Frequency and Period

Frequency and period are related by:

f=1Tf=\frac{1}{T}

Where:

  • ff = frequency in hertz (Hz).
  • TT = period in seconds (s).

For example, if a waveform has a period of 2,ms2\\,ms:

T=2,ms=0.002,sT=2\\,ms=0.002\\,s f=10.002=500,Hzf=\frac{1}{0.002}=500\\,Hz

The frequency is 500,Hz500\\,Hz.

Duty Cycle

Duty cycle is the percentage of a period during which a pulse signal remains active.

D=T_ONT×100%D=\frac{T\_{\text{ON}}}{T}\times100\%

For example, if a PWM signal is high for 3,ms3\\,ms in a total period of 10,ms10\\,ms:

D=310×100%=30%D=\frac{3}{10}\times100\%=30\%

The duty cycle is 30%30\%.

9. Understanding Oscilloscope Probes

An oscilloscope probe connects the test circuit to the instrument.

ZOYI P2060 BNC Oscilloscope Probe Kit User Manual

manuals.plus

Common probe types include:

  • Passive probe: Commonly used for general-purpose voltage measurements.
  • Active probe: Uses electronic circuitry to measure signals with particular bandwidth or loading requirements.
  • Differential probe: Measures voltage differences between two points when suitable common-mode and voltage ratings are respected.
  • Current probe: Measures current without inserting an ordinary voltage probe in series.

1× and 10× Probes

A switchable passive probe may offer two attenuation settings.

SettingEffect
1×Sends approximately the full signal voltage to the oscilloscope input
10×Attenuates the signal by a factor of ten before it reaches the input

A 10× probe generally reduces circuit loading and allows higher-frequency measurements than many 1× configurations, but the probe and oscilloscope must be configured correctly together.

For example, if a 10× probe measures a 5,V5\\,V signal, the instrument's displayed value should be 5,V5\\,V when the probe attenuation setting is correctly configured.

10. How to Measure a Signal Using an Oscilloscope

Follow these general steps for a low-voltage educational circuit.

  1. Turn on the oscilloscope.
  2. Connect a suitable probe to channel 1.
  3. Set the probe attenuation correctly on the instrument.
  4. Connect the probe tip to the signal point.
  5. Connect the probe's ground clip to the circuit's appropriate ground reference.
  6. Select a suitable volts/division setting.
  7. Adjust time/division until the waveform is visible.
  8. Adjust the trigger level and trigger mode to obtain a stable display.
  9. Use the measurement controls or grid to determine voltage, period, and frequency.

For a basic experiment, you could observe a low-voltage square wave generated by a microcontroller or signal generator.

Important: On many bench oscilloscopes, the probe ground clip is electrically connected to protective earth. Connecting it to the wrong point can short the circuit. Never attach a conventional grounded probe to a live mains conductor or an arbitrary high-voltage node. Use appropriately rated differential measurement equipment and proper safety procedures for such work.

11. Oscilloscope vs. Multimeter

Both instruments are useful, but they serve different purposes.

FeatureMultimeterOscilloscope
Main purposeMeasures electrical quantitiesDisplays and analyzes signals over time
Voltage measurementYesYes
Current measurementOften supported directly within ratingsUsually requires a suitable current probe or measurement setup
Resistance measurementYesGenerally no
Continuity testingCommonUsually no
Waveform displayNoYes
Frequency and timing analysisLimited on many modelsUsually available
Detecting short glitchesGenerally difficultPossible, depending on bandwidth, sample rate, and acquisition settings
Typical useBasic circuit testing and troubleshootingDetailed signal analysis

A multimeter is often the best starting point for simple checks, while an oscilloscope is better when the shape and timing of a signal matter.

12. Bandwidth and Sampling Rate

Two important specifications determine how well a digital oscilloscope can measure changing signals.

Bandwidth

Bandwidth indicates the frequency range over which the oscilloscope can reproduce signals within its specified response limits.

An oscilloscope with insufficient bandwidth may show a fast signal with rounded edges or an incorrect amplitude.

Sampling Rate

Sampling rate is the number of signal samples taken per second, commonly specified in samples per second (Sa/s).

A higher sampling rate can capture more detail, but it does not guarantee an accurate display by itself. The instrument also needs sufficient bandwidth, memory, and appropriate acquisition settings.

For repetitive waveforms, the Nyquist principle states that the sampling frequency must exceed twice the highest frequency component to avoid basic aliasing. In practice, accurate waveform shape and fast edges often require a much higher sampling rate.

13. Triggering in an Oscilloscope

Triggering determines when the oscilloscope begins capturing or displaying a waveform.

Without a suitable trigger, a repetitive signal may appear to move or scroll across the screen.

Common trigger types include:

  • Edge trigger: Starts acquisition when a signal crosses a specified voltage level in a rising or falling direction.
  • Pulse-width trigger: Triggers on pulses that meet selected duration conditions.
  • Video trigger: Synchronizes with supported video signals.
  • Pattern or logic trigger: Triggers on specified digital states, when supported.

For example, setting an edge trigger at 2,V2\\,V on a rising edge can help stabilize a square wave that crosses 2,V2\\,V as it rises.

14. Applications of Oscilloscopes

Oscilloscopes are used in many areas of electronics and engineering.

  • Microcontrollers: Inspect Arduino and ESP32 output signals.
  • PWM control: Measure duty cycle and switching frequency.
  • Power electronics: Examine converter switching behavior and ripple using suitable probes and measurement techniques.
  • Communication systems: Observe digital and analog signal timing.
  • Audio electronics: Inspect sound waveforms, distortion, and noise.
  • Robotics: Diagnose control signals sent to motor drivers and servos.
  • Embedded systems: Investigate timing problems and unexpected glitches.
  • Electronics repair: Compare signal behavior at different circuit points to help locate faults.

15. Advantages and Limitations

AdvantagesLimitations
Displays signal shape over timeUsually costs more than a basic multimeter
Measures timing and frequencyRequires practice to use effectively
Helps detect glitches and noiseHas finite bandwidth and sampling rate
Supports detailed troubleshootingIncorrect grounding can damage a circuit
Many models provide automatic measurementsProbe selection and setup affect accuracy

16. Safety and Measurement Considerations

  1. Check input ratings: Confirm the oscilloscope and probe support the voltage, frequency, and transient levels being measured.
  2. Understand grounding: A grounded probe can create a short circuit if its ground clip is attached to the wrong electrical point.
  3. Use appropriate probes: Match probe attenuation and ratings to the signal.
  4. Avoid exposed live circuits: High-voltage measurements require training and properly rated equipment.
  5. Check the displayed settings: Incorrect probe attenuation can cause voltage readings to be off by a factor of ten or another configured ratio.
  6. Choose appropriate time and voltage scales: Poor settings can hide details or make a waveform difficult to interpret.
  7. Do not assume a waveform is accurate just because it looks stable: Bandwidth, sample rate, triggering, and probe compensation all affect the result.

17. Summary

An oscilloscope is an essential instrument for observing and analyzing electrical signals over time. It displays voltage waveforms and helps measure amplitude, period, frequency, duty cycle, and signal timing.

Unlike a multimeter, which usually gives numerical readings, an oscilloscope reveals the shape of a signal and can expose noise, glitches, and timing problems. Understanding its probes, voltage and time scales, trigger settings, bandwidth, and sampling rate makes it much easier to troubleshoot circuits safely and accurately.

Keep learning. Keep building. Keep growing.

© 2026 Ugenz Academy