Ugenz Academy/IoT Tutorial

Series And Parallel Circuits

7 min read1,387 words

Reading progress

Keep learning

Series and Parallel Circuits

1. Introduction

An electric circuit is a complete path through which electric current flows. A circuit can contain a power source, wires, resistors, LEDs, switches, and other electronic components.

Based on how components are connected, circuits are mainly classified into two types:

  1. Series Circuit
  2. Parallel Circuit

Understanding these circuits is important because they determine how voltage, current, and resistance behave in an electrical system.

2. What Is a Series Circuit?

A series circuit is a circuit in which components are connected one after another, creating a single path for current to flow.

In a series circuit, the current passes through each component in sequence. There are no branches where the current can split.

For example, if three resistors are connected one after another to a battery, they form a series circuit.

Characteristics of a Series Circuit

  • There is only one path for current.
  • The same current flows through every component.
  • The supply voltage is divided among the components.
  • The total resistance is the sum of all individual resistances.
  • If one component breaks or disconnects, the entire circuit stops conducting current.

Total Resistance in a Series Circuit

The total resistance of a series circuit is calculated by adding the resistance of every resistor.

RT=R1+R2+R3+⋯+RnR_T=R_1+R_2+R_3+\cdots+R_n

Where:

  • RTR_T = total resistance
  • R1,R2,R3R_1,R_2,R_3 = individual resistances
  • nn = total number of resistors

Example:

Suppose three resistors are connected in series:

  • R1=10,ΩR_1=10\\,\Omega
  • R2=20,ΩR_2=20\\,\Omega
  • R3=30,ΩR_3=30\\,\Omega

The total resistance is:

RT=10+20+30R_T=10+20+30 RT=60,Ω\boxed{R_T=60\\,\Omega}

Therefore, the total resistance of the circuit is 60 ohms.

Current in a Series Circuit

The current is the same through every component in a series circuit.

IT=I1=I2=I3I_T=I_1=I_2=I_3

According to Ohm's law:

I=VRI=\frac{V}{R}

Suppose a 12 V battery is connected to the three series resistors whose total resistance is 60 Ω.

I=1260=0.2,AI=\frac{12}{60}=0.2\\,A

Therefore, the current flowing through each resistor is 0.2 A, or 200 mA.

Voltage in a Series Circuit

In a series circuit, the supply voltage is divided across the components. This is called voltage division.

The total supply voltage equals the sum of the voltage drops across all components.

VT=V1+V2+V3V_T=V_1+V_2+V_3

The voltage across each resistor can be calculated using Ohm's law:

V=IRV=IR

Using the previous example, the current is 0.2 A.

For the first resistor:

V1=0.2×10=2,VV_1=0.2\times10=2\\,V

For the second resistor:

V2=0.2×20=4,VV_2=0.2\times20=4\\,V

For the third resistor:

V3=0.2×30=6,VV_3=0.2\times30=6\\,V

The total voltage is:

VT=2+4+6=12,VV_T=2+4+6=12\\,V

This equals the battery's supply voltage.

Notice that the resistor with the highest resistance receives the largest voltage drop when the same current flows through all resistors.

3. What Is a Parallel Circuit?

A parallel circuit is a circuit in which components are connected across the same two electrical nodes, creating multiple paths for current.

Each branch is connected across the same supply voltage. Current divides among the available branches depending on their resistance.

For example, when three resistors are connected in separate branches across a battery, they form a parallel circuit.

Characteristics of a Parallel Circuit

  • There are multiple paths for current.
  • The voltage across each branch is the same.
  • The total current equals the sum of the branch currents.
  • The total resistance is less than the smallest individual resistance for two or more positive resistances in parallel.
  • If one branch becomes open, current can still flow through the other functioning branches.

Total Resistance in a Parallel Circuit

For resistors connected in parallel, the reciprocal of the total resistance equals the sum of the reciprocals of the individual resistances.

1RT=1R1+1R2+1R3\frac{1}{R_T}= \frac{1}{R_1}+\frac{1}{R_2}+\frac{1}{R_3}

For two resistors, this can be simplified to:

RT=R1R2R1+R2R_T=\frac{R_1R_2}{R_1+R_2}

Example:

Suppose two resistors are connected in parallel:

  • R1=6,ΩR_1=6\\,\Omega
  • R2=3,ΩR_2=3\\,\Omega

Using the formula:

RT=6×36+3R_T=\frac{6\times3}{6+3} RT=189R_T=\frac{18}{9} RT=2,Ω\boxed{R_T=2\\,\Omega}

The total resistance is 2 Ω, which is lower than either individual resistance.

For three or more resistors, use the reciprocal formula and then take the reciprocal of the result.

Voltage in a Parallel Circuit

The voltage across each branch of an ideal parallel circuit is equal to the supply voltage.

VT=V1=V2=V3V_T=V_1=V_2=V_3

Suppose three resistors are connected in parallel across a 12 V supply.

Each resistor receives 12 V, regardless of its resistance.

This is one of the main differences between series and parallel circuits: in a series circuit, voltage is divided; in a parallel circuit, each branch receives the full supply voltage.

Current in a Parallel Circuit

The total current entering the parallel network equals the sum of the currents through the branches.

IT=I1+I2+I3I_T=I_1+I_2+I_3

Each branch current is calculated using Ohm's law:

I=VRI=\frac{V}{R}

Suppose a 12 V supply is connected across two parallel resistors:

  • R1=6,ΩR_1=6\\,\Omega
  • R2=3,ΩR_2=3\\,\Omega

Current through the first resistor:

I1=126=2,AI_1=\frac{12}{6}=2\\,A

Current through the second resistor:

I2=123=4,AI_2=\frac{12}{3}=4\\,A

Therefore, the total current is:

IT=2+4=6,AI_T=2+4=6\\,A

The lower-resistance branch carries more current because both branches have the same voltage across them.

4. Series vs Parallel Circuits

FeatureSeries CircuitParallel Circuit
Current pathsOneMultiple
CurrentSame through every componentDivides among branches
VoltageDivided across componentsSame across each branch
Total resistanceSum of resistancesReciprocal formula
Adding another resistorIncreases total resistanceDecreases total resistance
Component failureAn open component can stop the entire circuitOther branches can continue working
Common applicationSome voltage-divider and current-limiting circuitsHousehold wiring and separate power branches

5. Combination Circuits: Series and Parallel Together

A circuit can contain both series-connected and parallel-connected components. This is called a series-parallel circuit or a combination circuit.

These circuits are common in practical electronics because different sections of a circuit may need different voltage, current, or resistance characteristics.

To calculate the total resistance:

  1. Identify resistors connected in series.
  2. Identify resistors connected in parallel.
  3. Simplify the parallel groups using the parallel-resistance formula.
  4. Add the resulting resistances that are connected in series.
  5. Continue simplifying until only one equivalent resistance remains.

Example:

Suppose a 4 Ω resistor is connected in series with a parallel combination of 6 Ω and 3 Ω resistors.

First, calculate the parallel combination:

RP=6×36+3=2,ΩR_P=\frac{6\times3}{6+3}=2\\,\Omega

Next, add the 4 Ω series resistor:

RT=4+2R_T=4+2 RT=6,Ω\boxed{R_T=6\\,\Omega}

The entire combination behaves like an equivalent 6 Ω resistance when viewed from the supply terminals.

6. Voltage Divider in a Series Circuit

A voltage divider is a circuit that uses series-connected resistors to produce a lower voltage from a supply voltage.

For two resistors connected in series, the output voltage across the second resistor is:

V_out=V_inR2R1+R2V\_{\text{out}}=V\_{\text{in}}\frac{R_2}{R_1+R_2}

Where:

  • V_inV\_{\text{in}} = input voltage
  • V_outV\_{\text{out}} = output voltage across R2R_2
  • R1R_1 and R2R_2 = series resistances

For example, suppose a 12 V supply is connected to a 1 kΩ resistor and a 2 kΩ resistor in series, with the output taken across the 2 kΩ resistor.

V_out=1220001000+2000V\_{\text{out}}=12\frac{2000}{1000+2000} V_out=8,V\boxed{V\_{\text{out}}=8\\,V}

The output is 8 V under the assumption that the output is not significantly loaded by another circuit.

Voltage dividers are used in sensor circuits, signal conditioning, and measuring circuits. However, they are not usually the best choice for supplying substantial current to a load because the output voltage can change when the load is connected.

7. Applications of Series and Parallel Circuits

Applications of Series Circuits

  • Voltage-divider circuits
  • Current-limiting resistors for LEDs
  • Battery cells connected in series to increase total voltage
  • Some string-light arrangements
  • Resistor networks used in electronic circuits

Applications of Parallel Circuits

  • Household electrical wiring
  • Separate lighting branches
  • Electronic circuits where components need the same supply voltage
  • Battery cells connected in parallel to increase available capacity, when the cells and protection system are designed for that use
  • Power distribution to multiple circuit sections

Household electrical appliances are generally connected in parallel so that each appliance receives the rated supply voltage and can operate independently of other appliances.

Keep learning. Keep building. Keep growing.

© 2026 Ugenz Academy