Ugenz Academy/IoT Tutorial

Field Effect Transistors

10 min read1,928 words

Reading progress

Keep learning

Field-Effect Transistors (FETs)

1. What Is a Field-Effect Transistor?

A Field-Effect Transistor (FET) is a semiconductor device used to control the flow of electrical current using an electric field.

FETs are commonly used as electronic switches, signal amplifiers, and voltage-control devices in modern electronic circuits.

Unlike a BJT, which uses base current to control collector current, a FET controls the current flowing through its channel primarily by applying a voltage to its control terminal.

A FET has three main terminals:

  • Gate (G): Controls the current flowing through the transistor.
  • Source (S): Supplies charge carriers to the channel in normal operation.
  • Drain (D): Receives charge carriers from the channel in normal operation.

Some FETs, especially certain MOSFETs, also have a fourth terminal called the body or bulk.

Feldeffekttransistor – RN-Wissen.de

rn-wissen.de

FETs are widely used in computers, microcontrollers, power supplies, motor controllers, amplifiers, and battery-powered devices.

2. Basic Working Principle of a FET

A FET contains a conducting region called a channel between the source and drain. The voltage applied to the gate controls the channel's conductivity.

For a common N-channel enhancement MOSFET:

  1. When the gate-to-source voltage is below the required threshold, the channel is normally OFF.
  2. When the gate-to-source voltage increases sufficiently, a conducting channel forms.
  3. As the gate voltage increases further, the channel can conduct more current, depending on the operating region and circuit conditions.
  4. Reducing the gate voltage reduces conduction, and the transistor can turn OFF.

BJT vs MOSFET: Which Is Better for Your Circuit?

jlcpcb.com

The gate controls the channel through an electric field. In a MOSFET, an insulating layer separates the gate from the semiconductor channel, so the steady-state gate current is ideally almost zero. Real devices still have leakage and require current to charge or discharge their gate capacitance during switching.

3. Types of Field-Effect Transistors

The two major FET families are:

2N3819 TO-92 Transistor JFET canal N - MEGATRONICA

1. Junction Field-Effect Transistor (JFET)

Uses a reverse-biased PN junction to control the channel. JFETs are normally ON at zero gate-to-source voltage and can be switched toward cutoff by applying the appropriate gate voltage.

IRFZ44N

2. Metal-Oxide-Semiconductor Field-Effect Transistor (MOSFET)

Uses an insulated gate to control the channel. MOSFETs are widely used in digital electronics and power switching because they can provide high input impedance and efficient switching.

4. Junction Field-Effect Transistor (JFET)

A JFET controls current through a semiconductor channel using an electric field created by a reverse-biased gate junction.

It is available in two types:

  • N-channel JFET
  • P-channel JFET

PPT - Introduction to FET’s PowerPoint Presentation, free download - ID:6611376

File:JFET P-Channel Labelled.svg - Wikimedia Commons

Fet full explanations | PPT

4

A. N-Channel JFET

An N-channel JFET uses an N-type channel, with P-type gate regions.

Its gate-to-source voltage is normally zero or negative during ordinary operation. Applying a more negative gate voltage widens the depletion regions, narrowing the conducting channel and reducing drain current.

At a sufficiently negative gate-to-source voltage, the channel reaches cutoff.

B. P-Channel JFET

A P-channel JFET uses a P-type channel, with N-type gate regions.

Its operating polarities are generally opposite to those of an N-channel JFET. Applying the appropriate positive gate-to-source voltage narrows the channel and reduces the drain current.

Characteristics of JFETs

  • Normally ON at zero gate-to-source voltage.
  • High input impedance.
  • Gate junction is normally reverse-biased.
  • Useful in low-noise amplifiers and analog circuits.
  • Available in N-channel and P-channel forms.

5. Metal-Oxide-Semiconductor Field-Effect Transistor (MOSFET)

A MOSFET is one of the most widely used transistor types in modern electronics.

Its gate is insulated from the semiconductor channel by a thin dielectric layer. This arrangement allows the gate voltage to control the channel without requiring substantial steady-state gate current.

MOSFETs are essential in microprocessors, memory circuits, switching power supplies, motor drivers, and many other electronic systems.

Main Types of MOSFETs

MOSFETs are divided into two operating types:

  1. Enhancement-mode MOSFET.
  2. Depletion-mode MOSFET.

Each type is available as an N-channel or P-channel device.

MOSFET - Working, Types, Operation, Advantages & Applications

electricaltechnology.org

A. Enhancement-Mode MOSFET

An enhancement-mode MOSFET is normally OFF when its gate-to-source voltage is zero.

For an N-channel enhancement MOSFET:

  • At V_GS=0V\_{GS}=0, the channel is normally OFF.
  • A sufficiently positive gate voltage forms a conducting channel.
  • Increasing the gate voltage beyond the threshold generally increases channel conductivity in the appropriate operating region.

For a P-channel enhancement MOSFET, the voltage polarities are reversed.

Applications: Power switching, microcontroller-controlled loads, motor drivers, and digital circuits.

B. Depletion-Mode MOSFET

A depletion-mode MOSFET has a conducting channel at zero gate-to-source voltage and is therefore normally ON.

For an N-channel depletion MOSFET, applying a sufficiently negative gate-to-source voltage can deplete the channel and reduce the current. A suitable positive gate voltage can increase conduction.

For a P-channel device, the voltage polarities are reversed.

Applications: Specialized analog circuits, constant-current circuits, and certain switching applications.

6. Difference Between Enhancement and Depletion MOSFETs

FeatureEnhancement ModeDepletion Mode
State at V_GS=0V\_{GS}=0Normally OFFNormally ON
Channel at zero gate voltageNot normally formedAlready exists
Gate voltageEnhances channel formationCan deplete or enhance the channel
Common useSwitching and digital circuitsSpecialized analog and switching circuits

7. N-Channel and P-Channel MOSFETs

MOSFETs can also be classified according to the channel's semiconductor type.

[MOSFET Symbol Explained: NMOS, PMOS & Diagram Guide

20262026

](https://images.openai.com/static-rsc-4/Mcp_vVtrDEVAAXE_9-XFvgXJ4X94wt9itHM6z0OvcNTlLNhdWQKhD6xa6WbSRjkJPnDwV2GKKIoRPq3o4Ts6vpVu4b18A5aPO1K7K6miWZH9PC78nq_OO9HZkFigX5aNTaaizhWF7nvaJ2NhUsrc3vATTNzhv7ICVsjF_5dA9Vk?purpose=inline)

Simbol litar FET (FET FIELD)

N-Channel MOSFET

An N-channel MOSFET uses electrons as its main charge carriers.

For a typical enhancement-mode device, the gate must be sufficiently positive relative to the source to turn it ON.

N-channel MOSFETs often have lower ON resistance than comparable P-channel devices of similar size and rating.

P-Channel MOSFET

A P-channel MOSFET uses holes as its main charge carriers.

For a typical enhancement-mode device, the gate must be sufficiently negative relative to the source to turn it ON.

P-channel MOSFETs are useful in high-side switching circuits, particularly when a simple control arrangement is preferred and their performance is suitable for the application.

Comparison

FeatureN-Channel MOSFETP-Channel MOSFET
Main charge carriersElectronsHoles
Typical turn-on polarityGate positive relative to sourceGate negative relative to source
Typical ON resistanceOften lowerOften higher
Common switching useLow-side switchingHigh-side switching
Conventional drain current when ONDrain to sourceSource to drain

These descriptions apply to typical enhancement-mode MOSFETs; depletion-mode devices have different default behavior.

8. Important MOSFET Parameters

ParameterMeaning
V_GSV\_{GS}Gate-to-source voltage
V_DSV\_{DS}Drain-to-source voltage
IDI_DDrain current
V_GS(th)V\_{GS(th)}Gate-to-source threshold voltage
R_DS(on)R\_{DS(on)}Drain-to-source resistance when the MOSFET is ON under specified conditions
V_DS(max)V\_{DS(max)}Maximum specified drain-to-source voltage
ID(max)I_D(max)Maximum specified drain current under stated conditions
PDP_DPower dissipation rating
QgQ_gGate charge, important for switching behavior

Important: The threshold voltage V_GS(th)V\_{GS(th)} does not mean the MOSFET is fully ON. It is measured at a very small specified drain current. To switch a load efficiently, select a MOSFET with an appropriate R_DS(on)R\_{DS(on)} at the available gate-drive voltage.

9. FET as an Electronic Switch

A FET can switch a load ON and OFF using a control voltage at the gate.

Consider an N-channel enhancement MOSFET used as a low-side switch.

LED Strip 3 MOSFETS "paralell" einschalten - Deutsch - Arduino Forum

forum.arduino.cc

Working

When the gate voltage is LOW:

  • The gate-to-source voltage is near zero.
  • The MOSFET is normally OFF.
  • The load current is blocked, apart from leakage.

When the gate voltage is sufficiently HIGH:

  • The gate-to-source voltage rises.
  • The channel becomes conductive.
  • Current flows through the load and MOSFET.
  • The load switches ON.

The gate should not be left floating because an undefined gate voltage can cause unwanted switching. A pull-down or pull-up resistor is often used, depending on the circuit.

For inductive loads such as motors and relays, suitable protection against voltage spikes is necessary.

10. FET as an Amplifier

A FET can also amplify small electrical signals.

In an amplifier circuit, a small change in gate voltage changes the drain current. A load resistor or another suitable load converts this current variation into an output-voltage variation.

FET Friday: Understanding the Common-Source JFET Amplifier

linearsystems.com

Common FET amplifier configurations include:

ConfigurationMain characteristic
Common sourceVoltage gain; output is typically inverted
Common drainAlso called source follower; voltage gain close to one
Common gateLow input impedance and useful high-frequency characteristics

FET amplifiers are used in sensor interfaces, audio circuits, radio-frequency systems, and other applications where high input impedance may be beneficial.

11. Difference Between BJT and FET

A BJT and a FET can both amplify signals and operate as electronic switches, but they control current differently.

FeatureBJTFET
Full formBipolar Junction TransistorField-Effect Transistor
TerminalsEmitter, base, collectorSource, gate, drain
Control methodBase current controls collector currentGate voltage controls channel current
Input impedanceGenerally lowerGenerally higher
Main charge carriersElectrons and holes participateDepends on device type
Steady-state control currentBase current is requiredGate current is ideally near zero for a MOSFET
Common applicationsAmplifiers and switchingSwitching, amplifiers, and integrated circuits

12. Advantages and Disadvantages of FETs

Advantages

  • High input impedance in many FET types.
  • MOSFETs can switch efficiently when properly selected and driven.
  • Require little steady-state gate current in MOSFET circuits.
  • Suitable for integrated circuits and high-density digital electronics.
  • Available in a wide range of small-signal and power devices.

Disadvantages

  • MOSFET gates can be damaged by electrostatic discharge.
  • Gate capacitance requires charging and discharging during switching.
  • Performance depends on voltage, current, and temperature.
  • Some FETs have higher ON resistance than others.
  • Correct gate-drive voltage and circuit design are essential for efficient operation.

13. Applications of Field-Effect Transistors

FETs are used in many areas of electronics:

  • Computers and processors: MOSFETs form the basis of modern digital logic and memory circuits.
  • Power supplies: Switching regulators use MOSFETs to control energy conversion.
  • Motor control: Power MOSFETs switch current through motors.
  • Microcontroller projects: Logic-level MOSFETs control LEDs, fans, and other suitable loads.
  • Audio systems: FETs amplify signals and can be used in input stages.
  • Sensors: High-input-impedance circuits can reduce loading on sensitive sensors.
  • Battery-powered devices: Efficient switching helps reduce power losses.
  • Communication equipment: FETs are used in radio-frequency amplifiers and signal circuits.

In summary: A field-effect transistor controls current through a semiconductor channel using an electric field. Its main families are JFETs and MOSFETs. FETs can operate as switches or amplifiers, and MOSFETs are especially important in modern digital electronics and power-control circuits.

Keep learning. Keep building. Keep growing.

© 2026 Ugenz Academy